Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

A quasi-direct numerical simulation solver for compressible reacting flows

Low Mach number lattice Boltzmann model for turbulent combustion: flow in confined geometries

Implementation and verification of an OpenFOAM solver for gas-droplet two-phase detonation combustion

Numerical Simulation for Combustion of Droplet with Volume of Fluid Formulation

Assessment of Numerical Accuracy and Parallel Performance of OpenFOAM and its Reacting Flow Extension EBIdnsFoam

Modified Reacting Solver: A Simplified Approach for Capturing the Molecular and Flow Diffusivities for the Nonpremixed MILD Flames

detonationFoam: An open-source solver for simulation of gaseous detonation based on OpenFOAM

High-order algorithms for compressible reacting flow with complex chemistry

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Flame simulations with an open-source code

Fragment-Based Ab Initio Molecular Dynamics Simulation for Combustion

Eulerian-Lagrangian modelling of detonative combustion in two-phase gas-droplet mixtures with OpenFOAM: validations and verifications

Accurate and rapid reactive flow simulations using dynamic load balancing and sparse analytical Jacobian approach

Direct Numerical Simulations and Analysis of Three-Dimensional N-Heptane Spray Flames in a Model Swirl Combustor

Implementation and assessment of a low-dissipative OpenFOAM solver for compressible multi-species flows

Development of a Chemistry Dynamic Load Balancing Solver with Sparse Analytical Jacobian Approach for Rapid and Accurate Reactive Flow Simulations

Fully explicit implementation of direct numerical simulation for a transient near-field methane/air diffusion jet flame

A Computational Framework for Interface-Resolved DNS of Simultaneous Atomization, Evaporation and Combustion

A Spectral Radius Scaling Semi-Implicit Iterative Time Stepping Method for Reactive Flow Simulations with Detailed Chemistry

Direct Numerical Simulation of Turbulent Boundary Layer Premixed Combustion under Auto-Ignitive Conditions

A mesh-free framework for high-order direct numerical simulations of combustion in complex geometries