Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

A Computational Framework for Interface-Resolved DNS of Simultaneous Atomization, Evaporation and Combustion

A DNS evaluation of mixing and evaporation models for TPDF modelling of nonpremixed spray flames

Numerical Simulation for Combustion of Droplet with Volume of Fluid Formulation

Direct numerical simulation of three-dimensional swirling n-heptane spray flames

Level Set Method for Atomization and Evaporation Simulations

Interface-resolved Detailed Numerical Simulation of Evaporating Two-Phase Flows with Robin Boundary Conditions on Irregular Domains

A numerical framework for modeling evaporation and combustion of isolated, spherically-symmetric, multi-component fuel droplets

A Coupled Vaporization Model Based on Temperature/species Gradients for Detailed Numerical Simulations Using Conservative Level Set Method

Accurate Level Set Method for Simulations of Liquid Atomization

Modeling Droplet Vaporization and Combustion with the Volume of Fluid Method at a Small Reynolds Number

DNS of swirling spray combustion

Recent Advances in Hybrid Eulerian–Lagrangian Description of Atomization

Direct Numerical Simulation of Swirling Liquid Atomization

Direct Numerical Simulations and Analysis of Three-Dimensional N-Heptane Spray Flames in a Model Swirl Combustor

A Generalized Coupled Level Set/volume-of-fluid/ghost Fluid Method for Detailed Simulation of Gas-Liquid Flows.

Simulation of Droplet-gas Flow in the Effervescent Atomization Spray with an Impinging Plate

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

An Enhanced Compressible Two-Phase Flow Model with Detailed Chemistry under the Adaptive Mesh Refinement Frame

Fully explicit implementation of direct numerical simulation for a transient near-field methane/air diffusion jet flame

Direct numerical simulations of swirling spray combustion under different conditions

A new robust modeling strategy for multi-component droplet heat and mass transfer in general ambient conditions