Abstract:Achieving a viable process for three-dimensional (3D) printing of ceramics is a sought-after goal in a wide range of fields including electronics and sensors for harsh environments, microelectromechanical devices, energy storage materials, and structural materials, among others. Low laser absorption of ceramic powders renders available additive manufacturing (AM) technologies for metals not suitable for ceramics. Polymer solutions that can be converted to ceramics (preceramic polymers) offer a unique opportunity to 3D-print ceramics; however, due to the low viscosity of these polymers, so far, their 3D printing has only been possible by combining them with specialized light-sensitive agents and subsequently cross-linking them layer by layer by rastering an optical beam. The slow rate, lack of scalability to large specimens, and specialized chemistry requirements of this optical process are fundamental limitations. Here, we demonstrate 3D printing of ceramics enabled by dispensing the preceramic polymer at the tip of a moving nozzle into a gel that can reversibly switch between fluid and solid states, and subsequently thermally cross-linking the entire printed part "at-once" while still inside the same gel. The solid gel, which is composed of mineral oil and silica nanoparticles, converts to fluid at the tip of the moving nozzle, allows the polymer solution to be dispensed, and quickly returns to a solid state to maintain the geometry of the printed polymer both during printing and the subsequent high-temperature (160 °C) cross-linking. We retrieve the cross-linked part from the gel and convert it to ceramic by high-temperature pyrolysis. This scalable process opens up new opportunities for low-cost and high-speed production of complex three-dimensional ceramic parts and will be widely used for high temperature and corrosive environment applications, including electronics and sensors, microelectromechanical systems, energy and structural applications.

Ceramic bodies without warping using epoxide‐acrylate hybrid ceramic slurry for photopolymerization‐based 3D printing

Photo‐cationic polymerizable ceramic slurry for the fabrication of ceramic structures in three‐dimensional printing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

3D printing of ceramics with controllable green‐body configuration assisted by the polyvinyl alcohol‐based physical gels

Development of ceramic-reinforced photopolymers for SLA 3D printing technology

Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing

Ceramic 3D Printing via Dye-Sensitized Photopolymerization Under Green LED

3D printing of high solid Al2O3 ceramics based on green and renewable photosensitive resin with low viscosity and low shrinkage

Optimizing photocuring properties of ceramic slurry for 3D printing of ceramic membranes

Sophisticated Structural Ceramics Shaped from 3D Printed Hydrogel Preceramic Skeleton

The 3D Printing Behavior of Photocurable Ceramic/Polymer Composite Slurries Prepared with Different Particle Sizes

Photopolymerization-based additive manufacturing of ceramics: A systematic review

A Comparative Study on 3D Printed Silicone-Epoxy/acrylate Hybrid Polymers Via Pure Photopolymerization and Dual-Curing Mechanisms

Fabrication of ceramics using photosensitive slurries: A comparison between UV-casting replication and vat photopolymerization 3D printing

Three-Dimensional Printing of Ceramics through "Carving" a Gel and "Filling in" the Precursor Polymer

Rheological behavior and curing deformation of paste containing 85 wt% Al2O3 ceramic during SLA-3D printing

Rheology and Printability of a Porcelain Clay Paste for DIW 3D Printing of Ceramics with Complex Geometric Structures

Study on Debinding and Sintering Processes for Ceramics Fabricated Using Digital Light Processing (DLP) 3D Printing

Photopolymerization-Based Three-Dimensional Ceramic Printing Technology

Fabrication and characterisation of ceramics via low-cost DLP 3D printing

Optimized Zirconia 3D Printing Using Digital Light Processing with Continuous Film Supply and a Recyclable Slurry System