Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Constructing interparticle hotspots through cracking silver nanoplates for laser initiation of explosives

Constructing hotspots through star-shaped gold-copper alloy nanocrystals for laser initiation of explosives

Laser ignition of energetic crystals of cyclotrimethylenetrinitramine (RDX) optically sensitized with gold nanoparticles and light-absorbing dye

Laser Initiation of RDX Crystal Slice under Ultraviolet and Near-Infrared Irradiations

Study on Characteristics of the Light-Initiated High Explosive-Based Pulse Laser Initiation

Ultraviolet Laser-induced ignition of RDX single crystal

Evolution of Oxidizing Inorganic Metal Salts: Ultrafast Laser Initiation Materials Based on Energetic Cationic Coordination Polymers

Explosive Decomposition of High Explosives with Ultrafine Metal Particle Inclusions under the Influence of Pulse Laser Radiation

Simulation of the ignition of organic explosives by a laser pulse in the weak absorption region

Laser triggered exothermic chemical reaction in Au nanoparticle@ Ti3C2 MXene membrane: A route toward efficient light to high-temperature pulse conversion

From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition

From nanoparticles to on-chip 3D nanothermite: electrospray deposition of reactive Al/CuO@NC onto semiconductor bridge and its application for rapid ignition.

Dependence of Energy Thresholds on Laser Radiation Wavelength in Initiation of Heavy Metal Azides

Modeling of high energy laser ignition of energetic materials

Core‐Shell Hetero‐Framework derived Copper Azide Composites as Excellent Laser‐Ignitable Primary Explosives

Safety Verification of Femtosecond Laser Cutting of Tungsten Alloys During the Dismantling of Decommissioned Energetic Materials

Electrostatic spraying synthesis of energetic RDX@NGEC nanocomposites

First-principles study of laser absorption characteristics of five typical explosives

Investigation of system parameters towards safer impact based shock-to-detonation transition in a novel laser driven flyer plate prototype

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Design and fabrication of energetic Al/Ni exploding foil with enhanced energy efficiency and plasma density for direct ignition