Abstract:The preparation of slurry from multi-source solid waste for underground backfill adds a way out for solid waste disposal, which is beneficial to reduce environmental impact. In this paper, the effects of gangue, fly ash, gasification coarse slag and desulfurization gypsum on the fluidity, early strength, thermal stability and other properties of the backfill slurry were studied by fluidity test, strength test, Thermo-Gravimetric Analysis (TGA), Scanning Electron Microscope (SEM) and X-ray Diffraction (XRD). The results show that: (1) When G/SW (mass ratio of gangue to solid waste) < 23%, gangue is beneficial to improve the fluidity and early strength of backfill slurry; with the increase of fly ash content, the fluidity of backfill slurry decreases, but its early strength increases; gasification coarse slag has a negative effect on the fluidity of backfill slurry, but it is beneficial to its early strength when GCS/SW (mass ratio of gasification coarse slag to solid waste) < 33%; desulfurization gypsum can improve the fluidity of the backfill slurry, but it is not conducive to the increase of early strength. (2) The compression failure mode of the backfill is mainly divided into the crack-intensive failure, the single main crack penetration splitting failure, and the double main crack conjugate splitting failure. (3) Endothermic dehydration reactions of adsorbed water and crystallization water generally occur at 55-65 °C and 110-130 °C for backfill with different solid waste contents; As the temperature continues to increase, the backfill material undergoes a slow exothermic decomposition reaction; Increasing the content of gangue, fly ash and gasification coarse slag and reducing the content of desulfurized gypsum can make the backfill less weight loss at high temperature and better thermal stability. (4) The main mineral phases in the backfill material are gypsum and quartz, and there are also a small amount of acicular and hexagonal hydration products thaumasite. After high temperature, the thaumasite is dehydrated and decomposed. The research results are helpful to deeply understand the performance of multi-source solid waste for underground backfilling.

Study on the influence mechanism of flue gas desulphurisation gypsum on solid waste-based geopolymer grouting materials

Experimental investigation on the mechanical performance and microscopic characterization of desulfurization gypsum-reinforced ternary geopolymer

Effect of Mineral Admixtures on Physical, Mechanical, and Microstructural Properties of Flue Gas Desulfurization Gypsum-Based Self-Leveling Mortar

Mechanical Properties and Coagulation Characteristics of Flue Gas Desulfurization Gypsum-Based Polymer Materials

A Study of the Influence of Cement Addition and Humidity on the Mechanical Strength and Microstructure of Flue Gas Desulfurization Gypsum–Cement Plasters

The effects of desulfurized gypsum on the mechanical properties of dredged clay with high initial water content stabilized by ternary geopolymer

Effect of desulphurization gypsum on hardening mechanism of the geopolymer produced with steel slag and granulated blast furnace slag

Effects of Different Admixtures on the Mechanical and Thermal Insulation Properties of Desulfurization Gypsum-Based Composites

Investigation on the effects of desulfurization gypsum on the engineering properties of ternary geopolymers: Improving the utilization of industrial wastes

Experimental Study on Mechanical Properties of Paste Backfill with Flue-Gas Desulphurisation Gypsum under Combined Action of Dry–Wet Cycles and Chloride Erosion

Investigation of mechanical, microscopic, and leaching properties of coal-based solid waste geopolymer mortar activated by soda residue and phosphogypsum

Study on the Mechanical Properties, Microstructure and Hydration Mechanism of Phosphogypsum-Based Geopolymer Cement with Added Micron-Sized Silica Particles

Effect of Waste Glass Powder and Bamboo Fiber on the Physico-Mechanical Properties and High-Temperature Behavior of a Fly Ash-Based Geopolymer

The Synergistic Mechanism and Stability Evaluation of Phosphogypsum and Recycled Fine Powder-Based Multi-Source Solid Waste Geopolymer

Solid waste-based dry-mix mortar using fly ash, carbide slag, and flue gas desulfurization gypsum

Utilization of untreated-phosphogypsum as filling and binding material in preparing grouting materials

Mitigation of efflorescence for multi-componential geopolymer: Influence of steel slag, flue gas desulfurization gypsum and pre-curing periods

Preparation and Performance Study of Alkali-active Gypsum Mixture System

Improving the mechanical property and water resistance of β-hemihydrate phosphogypsum by incorporating ground blast-furnace slag and steel slag

Study on the effect of multi-source solid waste on the performance of its backfill slurry

Enhance the mechanical and water resistance performance of flue gas desulfurization gypsum by quaternary phase