Abstract:Close-distance coal seams (CDCS) are widely distributed, and the layout of the upper and lower panels can be divided into "=" type and "+" type. The "+" superposition of upper and lower coal pillars in CDCS caused strong mine pressure, but there are few studies on the panel crossing residual coal pillars (RCP) when the upper and lower coal seams are "+" type layout. In view of the special spatial position ("+" type layout), this paper takes the typical panel 4-301 of a particular mine as the project indagation background and studies mining and crossing the overlying coal pillars by dint of field measurement, numerical simulation, indoor test, and engineering application. Compared with vertical stress or horizontal stress alone, the indexes of deviatoric stress and plastic zone can reflect the failure evolution of surrounding rock more comprehensively. Hence, this paper analyzes the expansion form of the plastic zone and the variation law of deviatoric stress before and after mining influence in the underlying mining roadway. The research results show that: (1) There is a sub-peak zone of deviatoric stress under the RCP. The deviatoric stress is bimodal in the range of 9 m below. After the peak value decays to 7.4 MPa, it changes to a single peak located in the area directly below the middle of the RCP. (2) The maximum plastic zones of the roof and two ribs of the roadway below the RCP are 3.4 m and 5 m, respectively. The crest value of deviatoric stress reaches 10 MPa. As the distance between the panel and the RCP decreases, the shape of the high deviatoric stress area presents the evolution law from the "ellipse" of the roof → the "crescent" of two ribs → the "cochlea" of the tips of the ribs. (3) When the mining of the underlying panel is 10 m, 0 m, or − 10 m away from the RCP (without passing through the RCP). The crest value of deviatoric stress within 5–10 m in advance of the roadway increases in turn. However, the peak value is significantly reduced when it is − 20 m away from the RCP (through the RCP). The crest value of deviatoric stress of two ribs decreases in turn along the panel rib → section coal pillar rib → solid coal rib. Based on this, the underlying 45 m of the RCP is divided into area I (10 m), area II (overlapping area 20 m), and area III (15 m) based on the degree of disturbance. And propose the technical scheme of asymmetric combined control in different zones by using asymmetric channel steel truss anchor cable for the top-ribs of areas I and III, and top-ribs asymmetric channel steel truss anchor cable + door-type support in area II. On-site project practice shows that the partitioned control technology successfully resisted the roadway instability and failure caused by the dynamic-static superimposed stress disturbance under the RCP and realized the primary support of the sectional coal roadway. The conclusion provides technical support and scheme design for the partitioning support of roadways under similar "+" type cross‐panels.

Research on the evolution of the deviatoric stress and control of a gas extraction roadway under mining influence

Study on Failure Mechanism and Control Technology of Roadway Surrounding Rock under Complex Occurrence Coal Seam

The J2 evolution model and control technology of the main roadway surrounding rock under superimposed influence of double-coal seam mining

Stability Control of Deep Coal Roadway under the Pressure Relief Effect of Adjacent Roadway with Large Deformation: A Case Study

Stress Evolution and Surrounding Rock Control During Coal Seam Mining Under the Influence of Overlying and Adjacent Goafs

Study on the Failure Mechanism for Coal Roadway Stability in Jointed Rock Mass Due to the Excavation Unloading Effect

Field and Numerical Study on Deformation and Failure Characteristics of Deep High-Stress Main Roadway in Dongpang Coal Mine

The evolution law of deviatoric stress and asymmetric control technology in roadways during panel mining through overlying residual coal pillars

Deformation mechanism and control technology of gob-side roadway with continuous mining and continuous backfilling: a case study

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

Experimental analysis of control technology and deformation failure mechanism of inclined coal seam roadway using non-contact DIC technique

Failure mechanism and stability control of surrounding rock in mining roadway with gentle slope and close distance

Study on stress distribution law of surrounding rock of roadway under the goaf and mechanism of pressure relief and impact reduction

Research on the evolutionary patterns and control of surrounding rock superimposed stress field local area loading in double-layer Island face main roadway

A Simulation Experimental Study on the Advance Support Mechanism of a Roadway Used with the Longwall Coal Mining Method

Research on large deformation mechanism of recovery roadway under mining stress conditions

True Triaxial Test and Research into Bolting Support Compensation Stresses for Coal Roadways at Different Depths

Gradient Failure Mechanism and Control Technology of Deep Roadways under the Action of Deviatoric Stress Field

Non-uniform failure and differential pressure relief technology of roadway under irregular goafs in deep close-distance coal seams

Surrounding Rock Control Technology of Thick Hard Roof and Hard Coal Seam Roadway under Tectonic Stress

Coupling control technology of anchoring and unloading in deep intense-mining and large-deformation roadway: a case study