Abstract:Close-distance coal seams (CDCS) are widely distributed, and the layout of the upper and lower panels can be divided into "=" type and "+" type. The "+" superposition of upper and lower coal pillars in CDCS caused strong mine pressure, but there are few studies on the panel crossing residual coal pillars (RCP) when the upper and lower coal seams are "+" type layout. In view of the special spatial position ("+" type layout), this paper takes the typical panel 4-301 of a particular mine as the project indagation background and studies mining and crossing the overlying coal pillars by dint of field measurement, numerical simulation, indoor test, and engineering application. Compared with vertical stress or horizontal stress alone, the indexes of deviatoric stress and plastic zone can reflect the failure evolution of surrounding rock more comprehensively. Hence, this paper analyzes the expansion form of the plastic zone and the variation law of deviatoric stress before and after mining influence in the underlying mining roadway. The research results show that: (1) There is a sub-peak zone of deviatoric stress under the RCP. The deviatoric stress is bimodal in the range of 9 m below. After the peak value decays to 7.4 MPa, it changes to a single peak located in the area directly below the middle of the RCP. (2) The maximum plastic zones of the roof and two ribs of the roadway below the RCP are 3.4 m and 5 m, respectively. The crest value of deviatoric stress reaches 10 MPa. As the distance between the panel and the RCP decreases, the shape of the high deviatoric stress area presents the evolution law from the "ellipse" of the roof → the "crescent" of two ribs → the "cochlea" of the tips of the ribs. (3) When the mining of the underlying panel is 10 m, 0 m, or − 10 m away from the RCP (without passing through the RCP). The crest value of deviatoric stress within 5–10 m in advance of the roadway increases in turn. However, the peak value is significantly reduced when it is − 20 m away from the RCP (through the RCP). The crest value of deviatoric stress of two ribs decreases in turn along the panel rib → section coal pillar rib → solid coal rib. Based on this, the underlying 45 m of the RCP is divided into area I (10 m), area II (overlapping area 20 m), and area III (15 m) based on the degree of disturbance. And propose the technical scheme of asymmetric combined control in different zones by using asymmetric channel steel truss anchor cable for the top-ribs of areas I and III, and top-ribs asymmetric channel steel truss anchor cable + door-type support in area II. On-site project practice shows that the partitioned control technology successfully resisted the roadway instability and failure caused by the dynamic-static superimposed stress disturbance under the RCP and realized the primary support of the sectional coal roadway. The conclusion provides technical support and scheme design for the partitioning support of roadways under similar "+" type cross‐panels.

What problem does this paper attempt to address?

The paper aims to address the issue of the impact of residual coal pillars (RCP) between upper and lower coal seams on the stability of lower coal mining roadways under the "+" layout conditions in close-distance coal seams (CDCS). Specifically: 1. **Background and Problem**: - Close-distance coal seams are widely distributed, and the spatial arrangement of upper and lower working faces can be divided into "=" type and "+" type. - When the upper and lower coal seams are arranged in a "+" type, the superposition of upper and lower coal pillars leads to strong mine pressure, but there is currently little research on crossing upper residual coal pillars. - Especially under the "+" layout conditions, the lower coal mining roadway suffers severe damage and deformation when crossing residual coal pillars. 2. **Research Object**: - The paper takes the typical working face 4-301 in a specific coal mine as the research background, using methods such as field measurement, numerical simulation, laboratory tests, and engineering applications to study the stress evolution law and plastic zone expansion form when crossing upper residual coal pillars. 3. **Main Findings**: - Deviatoric stress forms a sub-peak area below the residual coal pillars, showing a bimodal distribution within a range of 9 meters, and the peak value decays to 7.4 MPa before becoming unimodal. - The maximum plastic zones of the roof and two sides are 3.4 meters and 5 meters, respectively, with the deviatoric stress peak reaching 10 MPa. - As the distance between the working face and the residual coal pillars changes, the shape of the high deviatoric stress zone evolves from elliptical to crescent-shaped, and then to spiral. - The variation of the deviatoric stress peak at different distances is also different, and an asymmetric joint control technology scheme is proposed. 4. **Solution**: - An asymmetric joint control technology scheme is proposed for different regions, using asymmetric I-beam truss anchor cables for the support of the roof and two sides, and adding portal supports in the middle overlapping area. - Actual engineering applications show that this zonal control technology successfully resists the instability and damage of the roadway under the residual coal pillars, achieving preliminary support for the segmented coal roadway. In summary, the paper uses various methods to study in detail the stress evolution law when the lower coal mining roadway crosses residual coal pillars under the "+" layout conditions in close-distance coal seams, and proposes a corresponding asymmetric joint control technology scheme, providing technical support and design reference for roadway support under similar conditions.

The evolution law of deviatoric stress and asymmetric control technology in roadways during panel mining through overlying residual coal pillars

Failure mechanism and divisional differentiated control of surrounding rock in mining roadway under remaining coal pillar in close‐distance coal seam

Investigation on rational width of coal pillar and roadway support in isolated panel of extra-thick coal seam

Research on the evolutionary patterns and control of surrounding rock superimposed stress field local area loading in double-layer Island face main roadway

Study on roadway layout and surrounding rock control of isolated island panel

Non-uniform failure and differential pressure relief technology of roadway under irregular goafs in deep close-distance coal seams

Failure characteristics and stability control technology of dynamic pressure roadway affected by the mining activity: A case study

Control Technology of Soft Rock Floor in Mining Roadway with Coal Pillar Protection: A case study

Assessment of pillar stability and its control in a double roadway layout

Study on the instability mechanism and control technology of narrow coal pillar in double-roadway layout of Changping mine

Surrounding Rock Deformation Mechanism and Control Technology for the Roadway in the Fault-Disturbed Zone under Special-Shaped Coal Pillars

Study on small coal pillar in gob-side entry driving and control technology of the surrounding rock in a high-stress roadway

Failure mechanism and stability control of surrounding rock in mining roadway with gentle slope and close distance

Research on the evolution of the deviatoric stress and control of a gas extraction roadway under mining influence

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

The J2 evolution model and control technology of the main roadway surrounding rock under superimposed influence of double-coal seam mining

Experimental study on the movement law of overlying rock non-pillar coal overhead mining

Surrounding Rocks Deformation Mechanism and Roof Cutting-Grouting Joint Control Technology for Soft and Thick Coal Seam Roadway

Study on stress distribution law of surrounding rock of roadway under the goaf and mechanism of pressure relief and impact reduction

Study on Surrounding Rock Deformation Mechanism and Control of Roadway with Large Section and Extra-Thick Top Coal

Experimental analysis of control technology and deformation failure mechanism of inclined coal seam roadway using non-contact DIC technique