Abstract:Mechanical Performance of traditional gas-shielded arc welded joints of 700 MPa grade microalloyed C-Mn steel cannot meet service requirements. Laser welding, with its characteristic high energy density, is known to improve the welding performance of experimental steels. In the present study, Nb-Ti microalloyed steel with a thickness of 4.5 mm was welded using a 4 kW fiber laser. The microstructure, precipitation, and mechanical properties of the welded joints were studied. The hardness and tensile strength of the welded joints were higher than those of the base metal (BM). The microstructure of the fusion zone (FZ) and coarse grain heat affected zone (CGHAZ) was lath martensite (LM), while the microstructure of the fine grain HAZ and mixed grain HAZ consisted of ferrite and martensite/austenite islands. Although LM was observed in both the FZ and CGHAZ, the hardness and calculated tensile strength of the FZ were lower than those of the CGHAZ, due to a reduction in solid solution strengthening by element loss and the dissolution of high-hardness precipitates in FZ. Most precipitates such as [(Nb,Ti)C and (Nb,Ti)(C,N)] that were present in the BM were dissolved, which led to an increase in C and N in solid solution in the FZ. Thus, the elastic modulus of the FZ was higher than that of the BM. Similarly, the elastic modulus of the CGHAZ was higher than that of the BM due to the segregation of C and N atoms during the welding process. The toughness of the FZ was superior to that of the BM, and the toughness of the HAZ approached 91% of that of the BM. The change in toughness primarily depended on the microstructural refinement, the increase in the fraction of grains with high misorientation, the residual austenite in the FZ and CGHAZ, and the dissolution of coarse precipitates.

Role of Ni Content on Microstructure, Mechanical Property, and In‐Site Local Corrosion Behavior of Welded Joints Produced by Laser Welding of Dual‐Phase Steel

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Improving the Mechanical Properties of PHS Laser Welded Joints by Adding Ni Foil to Suppress Δ-Ferrite

Corrosion Behavior of High-Nitrogen Steel Hybrid Welded Joints Fabricated by Hybrid Laser-Arc Welding

Improving the Microstructure and Mechanical Properties of Laser-Welded Al–Si-Coated 22MnB5/Galvanized Steel Joints Added by Nickel

Effects of Laser Welding on the Microstructure Evolution and Corrosion Resistance of a Novel Nitrogen-Containing Austenitic Stainless Steel QN2109

Effect of Ni Foil Thickness on the Microstructure of Fusion Zone During PHS Laser Welding

The Microstructures and Mechanical Properties of Dissimilar Laser Welding of Copper and 316L Stainless Steel with Ni Interlayer

Effects of Interlaminar Microstructural Inhomogeneity on Mechanical Properties and Corrosion Resistance of Multi-Layer Fiber Laser Welded High Strength Low Alloy Steel

Effect of Ni addition on the microstructural evolution and lap-shear performance of AISI 630 martensitic stainless steel resistance spot welds

Mirostructure and Properties of Laser Welded Joints of Dual Phase and Press-Hardened Steels

Microstructures and mechanical properties of powder-filled laser welding joints composed of high-nitrogen steel

Laser-hybrid welding of 4716MA0 nickel-based alloy: effects of laser power on microstructure and properties

The Effect of Ni Foil on the Interface Microstructure and Mechanical Properties of Laser Lap Welded Steel/mg Joint

Microstructures and Mechanical Properties of Laser Penetration Welding Joint With/Without Ni-Foil in an Overlap Steel-on-Aluminum Configuration

Effect of process parameters on microstructure and properties of laser welded joints of aluminum/steel with Ni/Cu interlayer

Enhancing microstructural and mechanical characteristics of laser welded NiTi SMA/304 SS lap joints with medium and high entropy alloy fillers

Microstructure and Performance of Hybrid Laser-Arc Welded 40 Mm Thick 316 L Steel Plates

Impact of microstructure evolution on the corrosion behaviour of the Ti–6Al–4V alloy welded joint using high-frequency pulse wave laser

Effect of nitrogen content on microstructure, mechanical properties, and corrosion behaviour of coarse-grained heat-affected zone of nitrogen-containing austenitic stainless steel

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel