Abstract:Particle deposition on the surface of a drying chamber is the main drawback in the spray drying process, reducing product recovery and affecting the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber is investigated in this study. A hydrophobic polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless steel substrates, which were used to mimic the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, h) on the contact angle of the substrates (°), which reflected the hydrophobicity of the surface. A three-dimensional response surface was constructed to examine the influence of the PDMS concentration and treatment duration on contact angle readings, which serve as an indicator of the surface's hydrophobic characteristics. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination of a PDMS concentration of X1 = 1% (w/v) and treatment time of X2 = 4.94 h, while the PDMS coating for the stainless steel substrate achieved an optimum contact angle of 98.31° with a PDMS concentration of X1 = 1% (w/v) and treatment time of X2 = 1 h. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and a uniform nanostructure on the surface of the PDMS-treated substrates, which indicates the reduction in wettability and the potential effect of unwanted biofouling on the spray drying chamber. The application of PDMS and PTFE on the optimally coated substrates successfully reduced the amount of full cream milk particles that adhered to the surface. The low surface energy of the treated surface (19–27 mJ/m2) and the slightly higher surface tension of the full cream milk (54–59 mJ/m2) resulted in a high contact angle (102–103°) and reduced the adhesion work on the treated substrates (41–46 mJ/m2) as compared to the native substrates.

The Effect of Silica Powder Based on Methyltrimethoxysilane and Silica Sand as a Hydrophobic Material

Preparation and Research of Hydrophobic PDMS/Nano-SiO2 Modified SiO2 Coating

Fabricating Superhydrophobic and Oleophobic Surface with Silica Nanoparticles Modified by Silanes and Environment-Friendly Fluorinated Chemicals

Preparation of TEOS-GPTMS-PDMS Hybrid Material and Its Application in the Protection of Concrete

Statistical Approaching for Superhydrophobic Coating Preparation using Silica Derived from Geothermal Solid Waste

Synthesis and Characterization of Hydrophobic Silica Thin Layer Derived from Methyltrimethoxysilane (MTMS)

Condensation and hydrophobicity of the surface hydroxyl groups between organosilane modified water glass and microsilica

Preparation of a superhydrophobic coating based on polysiloxane modified SiO2 and study on its anti-icing performance

Design and preparation of multiple silica particles and study on superhydrophobic modified epoxy resin

Calcium Carbonate@silica Composite with Superhydrophobic Properties

Electrochemical and mechanical properties of superhydrophobic aluminum substrates modified with nano-silica and fluorosilane

Response Surface Optimisation of Polydimethylsiloxane (PDMS) on Borosilicate Glass and Stainless Steel (SS316) to Increase Hydrophobicity

Fabrication of mechanically robust superhydrophobic surfaces based on silica micro-nanoparticles and polydimethylsiloxane

Surface Modification to Produce Hydrophobic Nano-Silica Particles Using Sodium Dodecyl Sulfate As a Modifier

Fabrication of Superhydrophobic Coating Based on Waterborne Silicone-Modified Polyurethane Dispersion and Silica Nanoparticles

Preparation and Dispersion Performance of Hydrophobic Fumed Silica Aqueous Dispersion

Spray-coated Superhydrophobic Surfaces with Wear-Resistance, Drag-Reduction and Anti-Corrosion Properties

Super-Hydrophobic/Icephobic Coatings Based on Silica Nanoparticles Modified by Self-Assembled Monolayers

Preparation of hyperbranched hydrophobic nano-silica and its superior needling-effect in PDMS defoam agent

Preparation and anti-corrosion Properties of SiO2@MWCNTs@PFOTES Superhydrophobic Coatings on Magnesium Alloy

Dual hydrophilic/hydrophobic SiO2 transparent super-hydrophobic coating with good interfacial adhesion and high mechanical robustness