Abstract:PURPOSE:To evaluate the effect of surface treatment on bonding strength between pure titanium formed by selective laser melting and porcelain.METHODS:Pure titanium strips (64) and cobalt-chromium alloy strips (16) were laser machined to meet ISO 9693 standards. The pure titanium specimens were divided into 4 groups according to the sandblasting pressure and interlayer material. The sandblasting pressure of 0.25 MPa of bonder porcelain group was TB1, the sandblasting pressure of 0.25 MPa of gold coating group was TG1, the sandblasting pressure of 0.45 MPa of bonder porcelain group was TB2, and the sandblasting pressure of 0.45 MPa of the gold coating group was TG2(n=16). After porcelain fusing, half of the specimens in each group were tested for three-point bend bonding strength, and the other half were tested after 10 000 cycles of thermal cycling(n=8). The bonding strength of cobalt-chromium alloy after sandblasting at 0.25 MPa and 0.45 MPa was taken as the control group and recorded as group C1, C2(n=8). The bonding strength was tested using classical three-point bending experiment. The surface roughness of pure titanium was measured by laser scanning confocal microscope(LSCM). Field emission scanning electron microscopy(FE-SEM) was used to observe the interface morphology of titanium-ceramic. The surface morphology of titanium after porcelain stripping was observed with stereomicroscope and fracture modes were analyzed by it. Graphpad Prism 8.0 software package was used for statistical analysis of the data.RESULTS:The bonding strength of group TG2 was (40.16±3.97) MPa and (37.38±2.39) MPa of group TG1, which were significantly higher than that of group TB2 (36.32±1.44) MPa and group TB1 (33.75±2.31) MPa (P＜0.05). The bonding strength of group TB2 with 0.45 MPa sandblasting was significantly higher than that of group TB1 with 0.25 MPa sandblasting (P＜0.05). There was no significant decrease in titanium-ceramic bonding strength before and after thermal cycling. When the sandblasting pressure increased from 0.25 MPa to 0.45 MPa, the roughness increased significantly (P＜0.05). The fracture modes were mixed.CONCLUSIONS:Under the conditions of this study, gold coating can significantly improve the bonding strength of Ti22 porcelain and SLM pure titanium than bonder porcelain, and increase of sandblasting pressure can further improve the bonding strength of titanium-porcelain. After 10 000 cycles of thermal cycling, the titanium-porcelain bonding strength did not decrease significantly.

Glove contamination of etched porcelain surfaces and bond strength to enamel

Evaluating the effect of glove coating on the shear bond strength of porcelain laminate veneers

Surface preparation for orthodontic bonding to porcelain

Evaluation of the Bonding Shear Strength between Enamel and Dentin Feldspathic Porcelain and Two Different Monolithic Zirconia with Low and High Translucency

Influence of contamination and cleaning on bond strength to modified zirconia

Effect of different treatments of highly translucent zirconia on the bonding strength between zirconia and veneering porcelain

Effect of Surface Treatment on the Three-Point Bend Bonding Strength Between Pure Titanium Fabricated by Selec-Tive Laser Melting and Porcelain

Bond Strength to Lithium-Disilicate Ceramic after Different Surface Cleaning Approaches

Effect of Different Cleaning Methods on Shear Bond Strength of Resin Cement to Contaminated Zirconia

Effect of Different Cleaning Methods on Bond Strength and Surface Wettability of High Translucency Zirconia

[Effects of Saliva Contamination on Bond Strength of Resin-Resin Interfaces].

Effect of multiple firings on the shear bond strength of presintered cobalt-chromium alloy and veneering ceramic

Investigating the impact of different cleaning techniques on bond strength between resin cement and zirconia and the resulting physical and chemical surface alterations

Shear bond strengths of different types of adhesive resin agents to glass infiltrated alumina oxide ceramic

Influence of Surface Pretreatment on the Bond Strength of a Resin Luting Cement to Saliva-contaminated Enamel and Dentin

Effect of different ceramic surface treatments on the bond strength between resin and ceramic

Effects of extreme cooling methods on mechanical properties and shear bond strength of bilayered porcelain/3Y-TZP specimens

[Bond strength of etched enamel to direct composite resins, to indirect composite resins and to etched and silanized porcelain]

[The Bonding Characteristic of Titanium and RG Experiment Porcelain].

Bond strengths of porcelain to cobalt-chromium alloys made by casting, milling, and selective laser melting

Shear Bond Strength of Five Different Repair Systems to Three Different Ceramic Materials