Abstract:Abstract This study focuses on unveiling the interaction between injected CO2 and heavy oil through adequate phase behavior analyses. Moreover, the potential of CO2 EOR and CO2 storage were evaluated through injection scheme optimization and sensitivity analysis. Experimentally, the PVT experiments including CO2/heavy oil systems have been carried out to measure oil swelling, solubility, viscosity reduction, and density variation. The MMP of the heavy oil-CO2 mixture has been determined to provide the reference pressure for core displacements. CO2 injection experiments were conducted to examine the performance of CO2 enhanced recovery under different pressure. Different injection schemes were experimentally simulated including water flood, injection water followed by CO2 flooding, and injection water followed by CO2-WAG (water alternating CO2 flooding). Based on these studies, the sensitivity analysis was run on the validated model to examine the effects of different parameters including gas injection rate, CO2 slug size, and CO2-WAG cycle number on the heavy oil recovery and CO2 storage efficiency. As the saturation pressure of the heavy oil-CO2 mixture increases, the solubility of CO2 in heavy oil, the swelling, and the viscosity reduction increase at reservoir temperature (60°C). Although CO2 displacement efficiency and CO2 storage efficiency increase with increasing injection pressure, the increase in these two factors become significantly slower as pressure exceeds the MMP (30 MPa). Injection water followed by CO2-WAG increased oil recovery more than water flood or injection water followed by CO2 flooding. Only considering the influence of single factor conditions, the higher the injection CO2 rate, CO2 slug size, or WAG cycles number, the higher the cumulative oil production. However, based on comprehensive consideration of oil displacement rate, CO2 storage efficiency, CO2 cumulative storage, and cumulative WOR (water-oil ratio), reasonable injection CO2 rate, CO2 slug size, and WAG cycles number were finally optimized and screened out as 30,000 m3/day, 0.5 PV, and 5, respectively. The outcomes of this work provide valuable information for designing a suitable CO2 flooding strategy in heavy oil reservoir engineering applications. It also could bring significant economic and environmental benefits by improving oil recovery and reducing CO2 emissions.

Experimental and numerical studies on CO2 injectivity in low permeability oil reservoirs

Optimization Study of Injection-Production Parameters for CO2 Enhanced Oil Recovery and Storage in Low Permeability Oil Reservoirs

Study on enhancing oil recovery by CO2 injection in low permeability reservoir

Laboratory Study on the Oil Displacement Process in Low-Permeability Cores with Different Injection Fluids

Feasibility Study of Gas Injection in Low-Permeability Reservoirs of Changqing Oilfield

CO2-prepad injection EOR simulation and sensitivity analysis considering miscibility and geomechanics in tight oil reservoirs

A small-scale experimental study of CO2 enhanced injectivity methods of the high-rank coal

Characterization of Stages of CO2-Enhanced Oil Recovery Process in Low-Permeability Oil Reservoirs Based on Core Flooding Experiments

Characteristics and mechanisms of supercritical CO2 flooding under different factors in low-permeability reservoirs

Experimental and Modeling Study of CO2 EOR and CO2 Storage in Heavy Oil Reservoirs

Optimization of Carbon Sequestration and Carbon Displacement in Fractured Horizontal Wells in Low Permeability Reservoirs

Relative Permeability Characteristics During Carbon Capture and Sequestration Process in Low-Permeable Reservoirs

The injection capacity evaluation of high-pressure water injection in low permeability reservoir: numerical and case study

Experimental study on CO2 flooding characteristics in low-permeability fractured reservoirs

Experimental investigation of CO2 injection side effects on reservoir properties in ultra tight formations

Experimental and numerical study on influencing factors of replacement capacity and slickwater flowback efficiency using pre-CO2 fracturing in tight oil reservoirs

A numerical simulation study of CO2 injection for enhancing hydrocarbon recovery and sequestration in liquid-rich shales

Experimental investigation of CO2 storage and oil production of different CO2 injection methods at pore-scale and core-scale

A Minireview of the Influence of CO 2 Injection on the Pore Structure of Reservoir Rocks: Advances and Outlook

Geomechanical analysis of formation deformation and permeability enhancement due to low-temperature CO2 injection in subsurface oil reservoirs

Investigation of CO 2 -EOR and storage mechanism in Injection-Production coupling technology considering reservoir heterogeneity