Abstract:In this paper, a model of flood area display and damageevaluation is discussed, which adopts seed spread algorithm to calculate and visualize flood area based on a DEM data set and under the condition of a given water level of flood. The raster image containing flood area is overlaid with raster data converted from thematic vector maps such as land-use map and related to other socio-economic data, and then quantitative evaluation of flood damage is achieved. There are two different cases, the so-called “non-source flood” and “source flood”, for determining flood area based on DEM and under the given water level condition. Non-source flood corresponds to the case with well-distributed and large-area rainfall where all the low-lying land may have a flood disaster, and in this case all the points with elevations below the given water level should be included in the flood area. The “source flood” is the case of flood (e.g. from bank burst) flushing through the surrounding lands that needs to consider “ci rculating” condition. Because flood may be obstructed by ring structures or high lands, thus it can only cover the place where it flows and reaches. One of the computer processing methods suitable for source flood is the seed-spread algorithm. The principle of this method is to select a representative pixel as a seed and to examine its contiguous pixels outward along 4 or 8 directions. The pixels, contiguous to it and meeting the given conditions, become seeds, and then contiguous pixels to the new seeds will be examined in the same way. This process repeats until an aggregation of the pixels which meet the given conditions on a certain plane are obtained. Adopting seed spread algorithm for source-flood area calculation is just to achieve an aggregation of pixels, which satisfies the connectivity requirement and the given conditions of water level. The initial position of seed pixel should usually be selected on the characteristic points, e.g. adjacent to a reservoir dam or stream boundary. The precision of flood area calculation is mainly determined by spatial resolution of the DEM, the area on the ground is represented by each pixel; whereas the accuracy of flood area calculation, to a great extent, is dependent on the preci sion of the DEM's pixel value or elevation.Once the area below the flood water level has been calculated, the flood damage evaluation can be calculated by overlaying the flood range with thematic maps and by relating to other socio-economic data. All thematic maps were converted to raster data because algorithm of the overlay analysis implemented in raster format is relatively simple and computing is fast. In order to improve accuracy of the flood damage evaluation it is necessary to accurately register and georefer all raster layers before overlay analysis. The calculation results of flood damage evaluation are generally represented by tabulation, which is a kind of classified statistics of flood damage data, e.g. a table representing total area of every land-use type in different administrative divisions. The results of flood area calculation and damage evaluation can also be visually and dynamically provided in the forms of graph, image, 3D or virtual reality. The model has been successfully applied in the “Zhejiang Provincial Water Conservancy Management System” developed for a national project.

Construction of Water Pollution Monitoring Model after Flood Disaster Based on Big Data Analysis

Coupling Watershed Environmental Model with Optimizing Method to Provide Least Cost Alternatives in Environmental Planning and Management

Simulation of Water Quality in a River Network with Time-Varying Lateral Inflows and Pollutants

A GIS-based Method for Flooded Area Calculation and Damage Evaluation

A GIS Based Model for Calculating of Flood Area

A Real-Time, Dynamic Early-Warning Model Based on Uncertainty Analysis and Risk Assessment for Sudden Water Pollution Accidents

Research on Dynamic Early-warning Technology of Water Pollution Emergency Based on Pollutant Dispersion Simulation

Dynamic pollutant concentration correction method for river sudden pollution

Construction of pollution risk early warning model for urban drinking water supply chain

A real-time simulation model of water quality with the impact of internal pollution for water source reservoir

Evaluation of the water pollution risk of dam and dike-break floods in the inundated area

The application of big data in the analysis of the impact of urban floods: A case study of Qianshan River Basin

An Evaluation and Prediction Model of Water Quality

Source Identification of Accidental Water Pollution in a Tidal River Network Based on a Water Environment Model and Database

STUDY ON THE POLLUTION OF URBAN SCENIC WATER BODY BY MUNICIPAL DRAINAGE IN FLOOD SEASON AND ITS CONTROL PLANNING

Water Resources Risk Assessment Model based on the Subjective and Objective Combination Weighting Methods

Simulation of Sudden Water Pollution Accidents in Hunhe River Basin Upstream of Dahuofang Reservoir

Pollution Source Apportionment and Water Quality Risk Evaluation of a Drinking Water Reservoir during Flood Seasons

The Impact of Urbanization on Surface Runoff and Flood Prevention Strategies: A Case Study of a Traditional Village

[Water Quality Forewarning Model in the Framework of Water Pollution Forewarning DSS].

Model-Based Method to Establish Total Pollution Load Control Objective for Looped River Network