Abstract:The use of pre-alloyed powders as high-entropy alloy (HEA) coating precursors ensures a predetermined (unaltered) elemental composition of the coating with regard to the feedstock powder. At the same time, it is interesting to tackle a more challenging task: to form alloy coatings from powder blends (not previously alloyed). The powder-blend-based route of coating formation eliminates the need to use atomization or ball milling equipment for powder preparation and allows for the introduction of additives into the material in a flexible manner. In this work, for the first time, a HEA was obtained using detonation spraying (DS) followed by spark plasma sintering (SPS). A powder mixture with a nominal composition of 10Al-22.5Fe-22.5Co-22.5Ni-22.5Cu (at.%) was detonation-sprayed to form a multicomponent metallic coating on a steel substrate. The elemental composition of the deposited layer was (9 ± 1)Al-(10 ± 1)Fe-(20 ± 1)Co-(34 ± 1)Ni-(27 ± 1)Cu (at.%), which is different from that of the feedstock powder because of the differences in the deposition efficiencies of the metals during DS. Despite the compositional deviations, the deposited layer was still suitable as a precursor for a HEA with a configurational entropy of ~1.5R, where R is the universal gas constant. The subsequent SPS treatment of the substrate/coating assembly was carried out at 800–1000 °C at a uniaxial pressure of 40 MPa. The SPS treatment of the deposited layer at 1000 °C for 20 min was sufficient to produce an alloy with a single-phase face-centered cubic structure and a porosity of <1%. Interestingly, the hardness values of the as-sprayed and SPS-treated coatings were close to each other (~320 HV0.3). The hardness of the coatings measured in two perpendicular directions did not differ significantly. The features of the DS–SPS route of the formation of HEA coatings and its potential applications are discussed.

Development of competitive high-entropy alloys using commodity powders

High-entropy alloys fabricated via powder metallurgy. A critical review

A novel and sustainable method to develop non-equiatomic CoCrFeNiMox high entropy alloys via spark plasma sintering using commercial commodity powders and evaluation of its mechanical behaviour

Tailoring high-entropy alloys via commodity powders for metal injection moulding: A feasibility study

High Entropy Alloys: Laboratory to Industrial Attempt

Powder metallurgy of high-entropy alloys and related composites: A short review

Refractory high-entropy alloys fabricated by powder metallurgy: Progress, challenges and opportunities

Laser Powder Bed Fusion Processing of Low Cost CoCrFeNiMoxNby High Entropy Alloys with Promising High-Temperature Properties via In Situ Alloying Commercial Powders

Non-equiatomic high entropy alloys: Approach towards rapid alloy screening and property-oriented design

Fabrication of High Entropy Alloy by Powder Metallurgy Process

Industrial Development of High-Entropy Alloys

Alloy Design Strategies and Future Trends in High-Entropy Alloys

A new method of preparing high-performance high-entropy alloys through high-gravity combustion synthesis

Transitional and refractory elements-based high entropy alloy developed through mechanical alloying and microwave sintering: Tribological and corrosion responses

Fabrication of High-Entropy Alloys Using a Combination of Detonation Spraying and Spark Plasma Sintering: A Case Study Using the Al-Fe-Co-Ni-Cu System

Exploring the Compositional Space of High-Entropy Alloys for Cost-Effective High-Temperature Applications

High Strength and Ductility on Ni6W2Cr4Fe8Ti1 High Entropy Alloys by Selective Laser Melting

Selective electron beam melting of Al0.5CrMoNbTa0.5 high entropy alloys using elemental powder blend

Fabricating CoCrFeMnNi High Entropy Alloy Via Selective Laser Melting In-Situ Alloying

High entropy alloys: A review of preparation techniques, properties and industry applications

Using multicomponent recycled electronic waste alloys to produce high entropy alloys