Abstract:Charge balance is one of the most important factors for realizing high performance OLEDs. In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer and the electron transporting layer and thereby controlling the charge carrier supplies in the device. Red OLEDs with improved performance were achieved. Charge balance is one of the most important factors for realizing high performance organic light emitting devices (OLEDs). In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer (HIL) as well as the electron transporting layer (ETL) and thereby controlling the charge carrier supplies in the device. First, we develop a p‐dopant material (PD02), with a lowest unoccupied molecular orbit (LUMO) of −4.63 eV, much shallower than that of the commercial material (PD01) of which the LUMO is −5.04 eV. Nevertheless, this enables us to modulate the supply of holes to the emissive layer through tuning doping concentration. We demonstrate that device performances are significantly improved by employing such a scheme. With a 23% molar doping of PD02, a bottom emission red OLED achieves an external quantum efficiency (EQE) of over 30%, an operating voltage of 3.4 V and a LT95 ~15,000 h at 10 mA/cm2, with a Digital Cinema Initiative P3 (DCI‐P3) chromaticity of CIE (X, Y) = (0.68, 0.32). Moreover, the efficiency roll‐off is suppressed up till ~3500 cd/m2, a desirable feature in display applications. The lateral conductivity of by using such HIL is also found to be much lower than that of PD01, resulting in reduced crosstalk among RGB pixels. Next, a new electron transporting material (ETM‐02) with a deep LUMO of −2.86 eV is also introduced to further optimize the charge balance. Although devices with ETM‐02 shows lower voltage and higher EQE, lifetime is compromised. In order to improve lifetime, additional fine tuning of the charge balance is essential. Finally, a second p‐dopant PD03 with a LUMO of −4.91 eV is added to the HIL to further extend the modulation flexibility in the hole injection. A double‐layer HIL consisting of 8 nm of HTM:16% PD02 and 2 nm of HTM:3% PD03, where the former is in contact with anode, is adopted in the device structure. The bottom emission deep red device achieve EQE over 30%, an operating voltage of 3.2 V and an improved LT95 ~13,000 h at 10 mA/cm2 with a BT.2020 range chromaticity of CIE (X, Y) = (0.701, 0.299). In the double HIL configuration, the introduction of PD03 provides one more parameter for tuning and therefore improves the overall device performances.

PDY-132:F8T2 Polymer Blend Ultrafast Charge Transfer for Dipping OLED Turn-on Voltage: Consequences of Low Urbach Energy and Quicker Photoluminescence Dynamics

High-Efficiency Dual-Dopant Polymer Light-Emitting Diodes with Ultrafast Inter-fluorophore Energy Transfer

Highly Efficient Dual-Dopant Enhanced Emission OLEDs

Green Oled Based On Doped Tetra-Methylest& Of Perylene-3,4,9,10-Tetracarboxylicacid Emitter

Unexpectedly Slow Yet Efficient Picosecond to Nanosecond Photoinduced Hole-Transfer Occurs in a Polymer/Nonfullerene Acceptor Organic Photovoltaic Blend

Employing ∼100% Excitons in OLEDs by Utilizing a Fluorescent Molecule with Hybridized Local and Charge‐Transfer Excited State

Activating Energy Transfer Tunnels by Tuning Local Electronegativity of Conjugated Polymeric Backbone for High‐Efficiency OLEDs with Low Efficiency Roll‐Off

Efficient Blue Organic Light-Emitting Diodes Employing Thermally Activated Delayed Fluorescence

A Hybridized Local and Charge‐Transfer Excited State for Highly Efficient Fluorescent OLEDs: Molecular Design, Spectral Character, and Full Exciton Utilization

Peripheral Amplification of Multi-Resonance Induced Thermally Activated Delayed Fluorescence for Highly Efficient OLEDs

Electroluminescence Characteristics of A Blend System Based on A Novel Fluorene-Carbazole Copolymer and Pvk Doping System

Synergy between Photoluminescence and Charge Transport Achieved by Finely Tuning Polymeric Backbones for Efficient Light-Emitting Transistor

TADF dendronized polymer with vibrationally enhanced direct spin-flip between charge-transfer states for efficient non-doped solution-processed OLEDs

Versatile Thermally Activated Delayed Fluorescence Emitters via Non‐conjugated Extension Strategy Enabling OLEDs with Efficiency Over 37%

Ultrafast Electron Transfer in Low‐Band Gap Polymer/PbS Nanocrystalline Blend Films

Hybridization of Long‐Range and Short‐Range Charger Transfer Enables Efficient Thermally Activated Delayed Fluorescent and Hyperfluorescent OLEDs

Charge balance in OLEDs: Optimization of hole injection layer using novel p‐dopants

Rational Design of Aggregation-Induced Emission Luminogen with Weak Electron Donor-Acceptor Interaction to Achieve Highly Efficient Undoped Bilayer OLEDs.

Efficient Spin-Flip between Charge-Transfer States for High-Performance Electroluminescence, without an Intermediate Locally Excited State

2-phenylfuro[2,3-b]quinoxaline-triphenylamine based emitter: photophysical property and application for TADF-sensitized fluo-rescence OLEDs

Derivatives of 2-Pyridone Exhibiting Hot-Exciton TADF for Sky-Blue and White OLEDs