Abstract:It has been long understood that fretting differs from sliding wear in that the relative displacement between the bodies is generally smaller than the size of the contact between them, with debris ejection from the contact thus playing an important role in the behaviour of the contact in fretting. Whilst these ideas were clearly articulated more than 30 years ago via Godet's third-body approach and Berthier's concept of the tribology circuit, calculation of wear rates in fretting have continued to employ Archard's wear equation (or approaches directly derived from it), despite this approach assuming that the rate of wear is controlled by the rate of generation of wear debris (as opposed to the rate of its ejection from the contact). It has been shown recently that when debris ejection is the rate-determining-process in fretting, the instantaneous rate of wear is inversely proportional to a characteristic dimension of the wear scar. When non-conforming specimen pair geometries (such as cylinder-on-flat) are employed in fretting testing, the wear scar size increases as wear proceeds, and thus the instantaneous rate of wear decreases. In this paper, wear equations have been derived for three commonly employed non-conforming pair specimen geometries, which all take the form <math>Vw=KRn−1Edn</math> (<math>Vw</math> is the wear scar volume, <math>R</math> is the radius of the non-plane specimen(s) in the pair and <math>Ed</math> is the frictional energy dissipated) where <math>n</math> varies between 0.67 and 0.8 depending upon the geometry and assumptions made regarding the governing equation. It is argued that the assumptions on which the analysis is based are most valid for the cylinder-on-flat contact configuration with fretting perpendicular to the cylinder axis where the length of the line contact is large compared to the wear scar width. It is demonstrated that, despite the often apparently good fit of experimental data to an Archard-type equation, it is not appropriate to employ such Archard-type approaches to the analysis of fretting data in situations where debris ejection is the rate-determining-process. The equations derived in this paper relating wear scar size to some measure of the duration of the test should be used for such analysis instead of the linear relationships generally employed in previous work.

Ball-on-flat linear reciprocating tests: Critical assessment of wear volume determination methods and suggested improvements for ASTM D7755 standard

Large scale multi-parameter analysis of wear of self-mated 100Cr6 steel – A study of the validity of Archard's law

On the Use of Alternative Measurement Methods in the Estimation of Wear Rates in Rotary-Pin-on-Disk Tribometry

Statistical significance of the sliding wear test parameters under lubricated conditions on borided AISI 316 L-SS samples

Uncertainty-based comparison of conventional and surface topography-based methods for wear volume evaluation in pin-on-disc tribological test

An experimental framework for determining wear in porous journal bearings operated in the mixed lubrication regime

A Closer Look at the Contact Conditions of a Block-on-Flat Wear Experiment

EFFECTS OF SURFACE PREPARATION ON FRICTION AND WEAR IN DRY SLIDING CONDITIONS

New Tribological Aspects in the Micro-Areas of the Symmetric Rolling-Sliding Contact

Experimental investigations to assess surface fatigue failure in rolling contact bearing

Hybrid Tribotest Method for Realistically Measuring Friction and Wear of Heavy-Load Bearing Shells

A method to evaluate profilometric tooth wear measurements

A critical assessment of surface texturing for friction and wear improvement

Finite element analysis and experimental validation of polymer–metal contacts in block-on-ring configuration

Contact size and debris ejection in fretting: The inappropriate use of Archard-type analysis of wear data and the development of alternative wear equations for commonly employed non-conforming specimen pair geometries

Finite element implementation and validation of wear modelling in sliding polymer–metal contacts

Wear and surface degradation of commercial ZTA femoral heads under boundary lubrication conditions

Finite element analysis of sliding wear on the borided AISI 316L stainless steel

An approach to understanding tribological behaviour of dental composites through volumetric wear loss and wear mechanism determination; beyond material ranking

The Quantification of Physiologically Relevant Cross-Shear Wear Phenomena on Orthopaedic Bearing Materials Using the MAX-Shear Wear Testing System

Dry Sliding Friction and Wear Behavior of CuZn39Pb2 and AA7075 Under Industrial and Laboratory Conditions