Abstract:Electroactive polypyrrole (Pg) thin films were grown by potentiostatic electropolymerization at chemically derivatized interdigitated microsensor electrodes (IMEs) of gold on borosilicate glass leading to specific adhesion of the electroconductive polymer film to the device. Films were grown to a constant electropolymerization charge density of 70 mC/cm(2) at 0.65 V vs Ag-0/AgCl, 3 M Cl- from 1.0 M aqueous pyrrole solutions containing 2.5 mM poly(styrenesulfonic acid) (PSSA) and 2.5 mM dodecylbenzynesulfonate with the pH adjusted to 3.0 and the temperature maintained at 20 degrees C. The interdigit space of the IME devices was chemically derivatized by chemical modification with (3-aminopropyl)trimethoxysilane followed by direct linking of the primary amine to the carboxylic acid of 3-(1-pyrrolyl)propionic acid using the heterobifunctional linker 1,3-diisopropylcarbodiimide enhanced with N-hydroxysulfosuccinimide in aqueous solution. XPS evidence supports the immobilization of omega-(1-pyrrolyl) moieties to the device surface. The 3-(1-pyrrolyl)propionic acid was shown to be electroactive, electropolymerizable, and co-electropolymerizable with pyrrole monomer from aqueous solution. Electroconductive PPy films grown on these omega-(1-pyrrolyl) derivatized IME devices were allowed to bridge the interdigit space and so pyrrole monomer was co-electropolymerized with omega-(1-pyrrolyl) moieties specifically attached to the interdigit space of the device. This leads to specific adhesion of the PPy thin film to the device surface. Films grown in this way were compared to films similarly grown on unmodified devices, on IME: devices rendered hydrophobic by chemical modification with dodecyltrichlorosilane, and on devices modified with (3-aminopropyl)trimethoxysilane. Cyclic voltammetry revealed no significant difference in the electroactivity of PPy films grown on these various IME surfaces. Films were also characterized by the time to adhesive failure using the adhesive tape test following immersion in PBKCl 7.2 buffer or after being maintained dry under vacuum and over desiccating molecular sieves. The time to adhesive failure in both test environments occurred in the order unmodified < dodecyltrichlorosilane modified much less than (3-aminopropyl)trimethoxysilane modified much less than omega-(1-pyrrolyl) derivatized. The failure times were 3 days < 5 days much less than 27 days much less than 235 + days for films immersed in aqueous buffer and were 3 days < 36+ days much less than 235+ days much less than 235+ days for films stored dry under vacuum. The electrochemical and adhesion test evidence suggest that the PPy films are specifically immobilized to the omega-(1-pyrrolyl) derivatized IME: devices and that this negates the hydrolytic instability of the PPy/glass interface that leads to poor adhesion under physiologic conditions.

Tailoring Polypyrrole Film Characteristics with Multi-step Oxygen Plasma Treatment for High-Performance Strain Sensors: Impact on Bonding, Microstructure, and Electrical responsivity

A flexible strain sensor from polypyrrole-coated fabrics

Polypyrrole-coated Fabric Strain Sensor with High Sensitivity and Good Stability

Polypyrrole-coated Large Deformation Strain Fabric Sensor and Its Properties Study

Photothermal self-healable polypyrrole-polyurethane sponge with dynamic covalent oximino bonds for flexible strain sensors

Investigations of the Interface Design of Polyetheretherketone Filament Yarn Considering Plasma Torch Treatment

Alkali Treatment to Maximize Adhesion of Polypyrrole Coatings for Electro-Conductive Textile Materials

Dilute Polymerization of Aniline on PDMS Substrate via Surface Modification Using (3-Aminopropyl)Triethoxysilane for Stretchable Strain Sensor

Using Stretchable PPy@PVA Composites As a High-Sensitivity Strain Sensor to Monitor Minute Motion.

Dielectric barrier discharge plasma induced surface modification of polyester/cotton blend fabrics to improve polypyrrole coating adhesion and conductivity

PPY: PVA Blend Enhanced with Metal Salt for Gas Sensing Applications

Conductive Polymer Synthesis with Single-Crystallinity via a Novel Plasma Polymerization Technique for Gas Sensor Applications

A Study on the Oxygen Plasma Treatment on the Peel Adhesion Strength and Solder Wettability of SnBi58 Based Anisotropic Conductive Films

A Flexible and Wearable Strain Sensor from Polypyrrole‐Doped Elastomers with Dual Functions in Motion Monitoring and Thermotherapy

Design and Fabrication of Flexible Strain Sensor Based on ZnO-decorated PVDF Via Atomic Layer Deposition

Atomic-Level Insights of Polypyrrole Grafted InGaZnO Structure for ppb-Level Ozone Gas Sensing at Low Operating Temperature

Specific immobilization of electropolymerized polypyrrole thin films onto interdigitated microsensor electrode arrays

Influence of Oxygen Plasma Treatment on Poly(Ether Sulphone) Films

Effect of Ultrasonication Parameters on the Structural, Morphological, and Electrical Properties of Polypyrrole Nanoparticles and Optimization by Response Surface Methodology

Novel electronic skin based on PPy@PU nonwoven for strain sensing, photothermal and electrothermal applications

Electrospun Nanofibers and Spin Coated Films Prepared from Side-Chain Copolymers with Chemically Bounded Platinum (II) Porphyrin Moieties for Oxygen Sensing and Pressure Sensitive Paints.