Abstract:This work investigated the effect of Fe/Mn ratio on the microstructure and mechanical properties of non-equimolar Fe80−xMnxCo10Cr10 (x = 30% and 50%) high-entropy alloys (HEAs) fabricated by laser powder bed fusion (LPBF) additive manufacturing. Process optimization was conducted to achieve fully dense Fe30Mn50Co10Cr10 and Fe50Mn30Co10Cr10 HEAs using a volumetric energy density of 105.82 J·mm−3. The LPBF-printed Fe30Mn50Co10Cr10 HEA exhibited a single face-centered cubic (FCC) phase, while the Fe50Mn30Co10Cr10 HEA featured a hexagonal close-packed (HCP) phase within the FCC matrix. Notably, the fraction of HCP phase in the Fe50Mn30Co10Cr10 HEAs increased from 0.94 to 28.10%, with the deformation strain ranging from 0 to 20%. The single-phase Fe30Mn50Co10Cr10 HEA demonstrated a remarkable combination of high yield strength (580.65 MPa) and elongation (32.5%), which surpassed those achieved in the FeMnCoCr HEA system. Comparatively, the dual-phase Fe50Mn30Co10Cr10 HEA exhibited inferior yield strength (487.60 MPa) and elongation (22.3%). However, it displayed superior ultimate tensile strength (744.90 MPa) compared to that in the Fe30Mn50Co10Cr10 HEA (687.70 MPa). The presence of FCC/HCP interfaces obtained in the Fe50Mn30Co10Cr10 HEA resulted in stress concentration and crack expansion, thereby leading to reduced ductility but enhanced resistance against grain slip deformation. Consequently, these interfaces facilitated an earlier attainment of yield limit point and contributed to increased ultimate tensile strength in the Fe50Mn30Co10Cr10 HEA. These findings provide valuable insights into the microstructure evolution and mechanical behavior of LPBF-printed metastable FeMnCoCr HEAs.

Process Optimization of CoCrFeMnNi High Entropy Alloy Fabricated by Selective Laser Melting Based on Thermal Mechanism and Molten Pool Behavior Analysis

Selective Laser Melting (SLM) Additively Manufactured CoCrFeNiMn High-Entropy Alloy: Process Optimization, Microscale Mechanical Mechanism, and High-Cycle Fatigue Behavior

The manufacturing process optimization and the mechanical properties of FeCoCrNi high entropy alloys fabricated by selective laser melting

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Selective laser melting of the Al0.3CoCrFeNiCu high-entropy alloy: Processing parameters, microstructure and mechanical properties

In-situ synthesis of CoCrFeMnNi high-entropy alloy by selective laser melting

Microstructure and Mechanical Properties of FeCoNiCrAlx High-entropy Alloys by Selective Laser Melting

Crack Formation and Control in an AlCoCrFeNi High Entropy Alloy Fabricated by Selective Laser Melting

Laser metal deposition of thin-walled parts of Al 0.8 CrFe 2 Ni 2 high-entropy alloy: Process window, microstructure, wear resistance and mechanical anisotropy

Dynamic mechanical properties and σ precipitates strengthening of a NiCrFeCoMo 0.2 high-entropy alloy additively manufactured by selective laser melting

Microstructure and mechanical properties of AlCoCrFeMnNi HEAs fabricated by selective laser melting

Effects of Process Parameters on Microstructures and Tensile Properties of Laser Melting Deposited CrMnFeCoNi High Entropy Alloys

Study on laser shock modulation of melt pool in laser additive manufacturing of FeCoCrNi high-entropy alloys

The Effect of Laser Remelting during SLM on Microstructure and Mechanical Properties of CoCrFeNiNb0.25

Progress of high-entropy alloys prepared using selective laser melting

Rapid prediction of the relationship between processing parameters and molten pool during selective laser melting of cobalt-chromium alloy powder: Simulation and experiment

A Physical Mechanism-Based Model of CoCrFeMnNi High Entropy Alloy Considering Adiabatic Heat Effect for Hot Bulk Forming Processes

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

High-strength Fe32Cr33Ni29Al3Ti3 fabricated by selective laser melting

The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing

Microstructure, mechanical and tribological properties of CoCrFeNi high-entropy alloy fabricated by different preparing processes