Abstract:Sodium-sulfur (Na-S) batteries have been commercialized for stationary energy storage systems because of their low-cost fabrication and long-cycling stability. However, the Na-S batteries need to operate at high temperatures (> 300 o C) to maintain the molten state of sodium anode and sulfur cathode, which requires extra energy and raises safety issues when the solid electrolyte membrane fails. Therefore, low-temperature all-solid-state Na-S batteries (such as 60 o C) are highly desirable because of the improved safety and a lower operating temperature. To achieve high sulfur-specific capacity and long-cycling stability, the stable interfaces between electrodes and solid-state electrolyte are important for all-solid-state Na-S batteries. Herein, we demonstrate a strategy using Na alloy anodes to replace Na metal anode to solve the issues of unstable interface between Na metal and solid-state electrolytes. Na-Sn and Na-Sb alloys are first compared in terms of their alloying/dealloying process to identify the advantage of Na-Sb alloy as the anode. The Na-Sb alloy anode shows its superior stability against the solid electrolyte and undergoes a stable Na alloying/dealloying process at 0.04 mA cm -2 for over 500 hours. Sulfur-carbon composites with confined sulfur nanostructure were synthesized via the sulfur vapor deposition method and further utilized in full cells. Combining the optimized Na-Sb alloy anode and sulfur composite cathodes, the all-solid-state Na alloy-S battery shows improved rate performance and a high sulfur-specific capacity of 1377 mAh g -1 with good capacity retention of 70 % after 180 cycles at 60 o C (Figure 1a and b). Postmortem analysis of both the anode and cathode shows a reversible discharge/charge process after the first cycle and undergoes significantly rearranged distributions of carbon and solid electrolytes after 180 cycles due to severe volume change induced by repeated sodiation/desodiation process. These research results show a high sulfur specific capacity with long-cycling stability and shed light on further improving next-generation Na-S energy storage systems. Figure 1

Tailoring Na+ Solvation Environment and Electrode–Electrolyte Interphases with Sn(OTf)2 Additive in Non‐flammable Phosphate Electrolytes towards Safe and Efficient Na–S Batteries

Non-flammable electrolyte for dendrite-free sodium-sulfur battery

Stable room-temperature sodium-sulfur battery enabled by pre-sodium activated carbon cloth anode and nonflammable localized high-concentration electrolyte

Electrolytes with Solvating Inner Sheath Engineering for Practical Na-S Batteries

Stable Dendrite‐Free Room Temperature Sodium‐Sulfur Batteries Enabled by a Novel Sodium Thiotellurate Interface

Amorphous FeSnOx Nanosheets with Hierarchical Vacancies for Room‐Temperature Sodium‐Sulfur Batteries

Rational Electrolyte Design Toward Cyclability Remedy for Room‐Temperature Sodium–Sulfur Batteries

Fluorinated ester additive to regulate nucleation behavior and interfacial chemistry of room temperature sodium-sulfur batteries

Tuning the solvation structure with salts for stable sodium-metal batteries

An in-situ formed stable interface layer for high-performance sodium metal anode in a non-flammable electrolyte

Construction of Robust Solid-Electrolyte Interphase via Electrode Additive for High-Performance Sn-Based Anodes of Sodium-Ion Batteries

A Safer Sodium-Ion Battery Based on Nonflammable Organic Phosphate Electrolyte

Nucleophilic Sn Seeding and Interface Engineering for Highly Stable Sodium Metal Batteries

Development of Stable All-Solid-State Sodium-Sulfur Batteries

Tailoring Na-ion Flux Homogenization Strategy Towards Long-Cycling and Fast-Charging Sodium Metal Batteries

Promoting Cathodic Kinetics and Anodic Stability in Practical Room-Temperature Sodium-Sulfur Batteries with Bifunctional Electrolytes

A Polysulfides‐Defensive, Dendrite‐Suppressed, and Flame‐Retardant Separator with Lean Electrolyte for Room Temperature Sodium–Sulfur Batteries

O‐Tailored Microstructure‐Engineered Interface toward Advanced Room Temperature All‐Solid‐State Na Batteries

Encapsulating Sulfides into Tridymite/Carbon Reactors Enables Stable Sodium Ion Conversion/Alloying Anode with High Initial Coulombic Efficiency Over 89%

Solvent Reorganization and Additives Synergistically Enable High-Performance Na-Ion Batteries

Phase‐Transition Interlayer Enables High‐Performance Solid‐State Sodium Batteries with Sulfide Solid Electrolyte