Abstract:<p>The temperature rise of the working coil due to Joule heating is a very important issue in electromagnetic forming processes. A technically simple and cost-effective method was proposed to address this problem, which only needs to introduce an additional resistor in the discharge circuit. The core of this method is to alter the current waveform during the forming process by adjusting the damping coefficient of the discharge circuit. The effectiveness of the method was numerically analyzed in detail and verified by the experimental investigations. It has been demonstrated that the Joule heating in the coil can be significantly reduced when a resistor was applied, while ensuring the forming depth of workpiece unchanged. As an example, more than 50% of the Joule heating in a bobbin coil can be decreased when a resistor of 400 mΩ is applied. Meanwhile, the versatility of the developed method was further verified through the analysis of an electromagnetic forming system with a spiral coil and a high-frequency discharge. Furthermore, this work found that the line resistance of discharge circuit should not be as small as possible. It has been proved that when the line resistance is already small, further reducing it has little effect on the improvement of forming efficiency, but it will greatly increase the Joule heating in the coil. The developed method of achieving adjustable current waveform and its application in reducing the Joule heating of coil could be of great significance to the development of electromagnetic forming.</p>

What problem does this paper attempt to address?

The paper primarily focuses on addressing the issue of temperature rise in the work coil due to Joule heating effect during the Electromagnetic Forming (EMF) process. During EMF, the large currents generated in the coil lead to significant Joule heating, which in turn causes the coil temperature to rise, especially in batch production requiring short cycle times. The increase in coil temperature negatively impacts the performance of coil materials (conductors, insulating materials, and reinforcing materials), making it crucial to understand and develop methods to reduce coil temperature to ensure safe and reliable operation of the coil in practical applications. The paper proposes a technically simple and cost-effective method to solve this problem by introducing an additional resistor into the discharge circuit. The core of this method lies in adjusting the damping coefficient of the discharge circuit to alter the current waveform during the forming process. Numerical analysis has thoroughly verified the effectiveness of this method, and it has been confirmed through experimental studies. The results show that when a resistor is applied, the Joule heating in the coil can be significantly reduced while maintaining the forming depth of the workpiece unchanged. For example, when a 400 milliohm resistor is applied, the Joule heating in the solenoid coil can be reduced by over 50%. Furthermore, the universality of the developed method has been further verified by analyzing spiral coils and electromagnetic forming systems with high-frequency discharge. Additionally, the paper finds that the line resistance of the discharge circuit should not be as small as possible. When the line resistance is already low, further reducing it has little effect on improving forming efficiency but significantly increases Joule heating in the coil. The developed adjustable current waveform method and its application in reducing coil Joule heating are of significant importance for the development of electromagnetic forming.

Adjustable current waveform via altering the damping coefficient: A new way to reduce Joule heating in electromagnetic forming coils

Magnet circuit design and optimization of giant magnetostrictive transducer

A Dual-Loop Waveform Distortion Suppression Method for Electromagnetic Vibrators at Low Frequencies

The importance of coil conductivity and eddy current effects in the analysis of electromagnetic forming process

Controlling Voltage Computation in Electromagnetic Induction Heating

A Study on the Method of Temperature Distribution Control in Electromagnetism Induction Heating

Coil-less electromagnetic forming process with uniform-pressure characteristics for shaping sheet metals

Design and Experiments of Electromagnetic Heating Forming Technology

Electromagnetic attractive forming of aluminum alloy sheets utilizing a low-frequency half-wave current

Effect of pulse width of middle-coil current on deformation behavior in electromagnetic tube forming under two-stage coils system

Optimization of a Single-Switch Wireless Power Transfer Circuit Based on a Multi-Coil Array

External Magnetic Field Minimization for the Integrated Magnetics in Series Resonant Converter

Improvement on formability and forming accuracy in electromagnetic forming of deep-cavity sheet metal part using a dual-coil system

Direct pulse current electromagnetic forming (DPCEMF): a novel electromagnetic forming technology for aluminum alloy sheet

A Continuously Magnetic Valve Arc-Suppression Coil and Its Modeling

A Novel Temperature Rise Calculation Method of Electromagnet DC Coil

Highly Effective Leakage Magnetic Field Suppression by Using a Reactive Coil in Perfectly Aligned EV Wireless Charging Systems

Micromachined structures decoupling Joule heating and electron wind force

Topological optimization of magnetic pulse welding coils for maximizing the effective weld area with a discretized differential evolution algorithm

Eliminating warping due to stamping by using pulsed radial magnetic force