Abstract:Protonic ceramic electrolysis cells (PCECs) have been attracting attention due to their ability to operate in the intermediate temperature (300 - 500 ̊C) sweet-spot. These temperatures enable fast kinetics, inexpensive materials (no precious metals; stainless interconnects), and lower operating voltage for producing green hydrogen, without the accelerated degradation that may be observed at higher temperatures. The steam electrodes often support triple conduction and thereby host the proton exchange / oxygen evolution process at the surface, where steam is split. Steam electrode materials development is at a relatively early stage, with open questions around the relationships among bulk composition, evolving surface chemistry, kinetic quantities, and degradation mechanisms. We are investigating the proton exchange surface coefficient ( k ) and its evolution over time on model thin film electrodes in order to ultimately develop highly active and long-term stable steam electrodes for PCECs. ABO 3 perovskites with Ba on the A-site and nominally multivalent ions on the B-site are candidates for steam electrodes given the varied compositions in this class that can transport oxide ions, protons, and electronic species, and the lowering of hydration enthalpies by the basicity introduced by Ba. However, very few measurements of k exist for these materials, and the evolution of surface chemistry and thus k is poorly understood. In this work, we fabricated and compared two perovskite triple conducting oxides by growing geometrically well-defined films of Ba(Pr,Y)O 3-x (BPY) and Ba(Co,Fe,Zr,Y)O 3-x (BCFZY) with pulsed laser deposition. We examined the proton surface exchange coefficients ( k -values) using simultaneous in-situ optical transmission relaxation and electrical conductivity relaxation measurements upon switching pH 2 O at a temperature of 400 ̊C, and continued these switches as a function of time to assess stability. To our knowledge, this is the first use of an optical transmission method to probe elevated temperature steam splitting kinetics, and we interpret the optical (and electrical) changes as indicative of redox during the hydrogenation process. The k -values of BPY thin films were approximately ten times higher than those of the BCFZY thin films, and BPY also retained higher k -values over time. The bulk and surface chemical compositions of BPY and BCFZY thin films before and after relaxation measurements were compared using Rutherford backscattering spectrometry, angle-resolved X-ray photoelectron spectroscopy, and scanning transmission electron microscopy with spectroscopy. Pronounced Ba enrichment and Si contamination (from the quartz tube) were evident at the surface of BPY by both S/TEM-EDS and XPS, whereas for BCFZY these surface chemical features were only detectable by XPS and absent in S/TEM-EDS. Implications for materials design of steam electrodes will be discussed, considering efficiency and lifetime.

Deconvolution of Water-Splitting on the Triple-Conducting Ruddlesden–Popper-Phase Anode for Protonic Ceramic Electrolysis Cells

Layer-structured triple-conducting electrocatalyst for water-splitting in protonic ceramic electrolysis cells: Conductivities vs. activity

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple-Conducting Oxides for Protonic Ceramic Electrochemical Cells

High-temperature Water Oxidation Activity of a Perovskite-Based Nanocomposite Towards Application As Air Electrode in Reversible Protonic Ceramic Cells

One-pot Derived Thermodynamically Quasi-Stable Triple Conducting Nanocomposite As Robust Bifunctional Air Electrode for Reversible Protonic Ceramic Cells

Triple conducting perovskite Ba0.95La0.05Fe0.8Zn0.2O3−δ as oxygen electrode for reversible protonic ceramic cells

(Invited) Proton Surface Exchange Kinetics and Stability of Thin-Film Triple Conducting Oxides for Protonic Ceramic Electrolysis Cells

Magnesium Tuned Triple Conductivity and Bifunctionality of BaCo0.4Fe0.4Zr0.1Y0.1O3-δ Perovskite Towards Reversible Protonic Ceramic Electrochemical Cells

Single-phase La0.8Sr0.2Co1-xMnxO3-δ Electrocatalyst As a Triple H+/O2-/e-conductor Enabling High-Performance Intermediate-Temperature Water Electrolysis

A Synergistic Three-Phase, Triple-Conducting Air Electrode for Reversible Proton-Conducting Solid Oxide Cells

Investigation of Water Impacts on Surface Properties and Performance of Air‐Electrode in Reversible Protonic Ceramic Cells

Surface Self-Assembly Protonation Triggering Triple-Conductive Heterostructure with Highly Enhanced Oxygen Reduction for Protonic Ceramic Fuel Cells

Highly Active Nanocomposite Air Electrode with Fast Proton Diffusion Channels Via Er Doping‐Induced Phase Separation for Reversible Proton Ceramic Electrochemical Cells

A New In Situ Synthetic Triple-Conducting Core–Shell Electrode for Protonic Ceramic Fuel Cells

Interfacial Engineering of Protonic Ceramic Electrochemical Cells by Acid Etch

Synergistic dual-phase air electrode enables high and durable performance of reversible proton ceramic electrochemical cells

Synergistic Bulk and Surface Engineering for Expeditious and Durable Reversible Protonic Ceramic Electrochemical Cells Air Electrode

Regulation of Ni/Co Ratio and Gas Transport in High‐Order Ruddlesden–Popper Perovskite Air Electrodes for Protonic Ceramic Electrochemical Cells

An Efficient High‐entropy Perovskite‐type Air Electrode for Reversible Oxygen Reduction and Water Splitting in Protonic Ceramic Cells

A Novel Triple-Conductive Cathode with High Efficiency and Stability for Protonic Ceramic Fuel Cells

An Active and Robust Air Electrode for Reversible Protonic Ceramic Electrochemical Cells