Abstract:The PEM electrolyzers are considered a promising alternative to alkaline water electrolyzers, as the advantages of PEM technology are high efficiency, high power density, a wide range of power inputs, low operating temperatures, relatively quick start-up, and easy scale-up. The ability of PEM electrolyzers to function dynamically makes them particularly appealing in energy capture and storage systems where electrical energy is derived from renewable sources such as solar and wind power. The bipolar plates (BPPs) are essential components of the PEM electrolyzer stacks and account for the main fraction of the total weight and cost. The BPPs must be electrically conductive, highly corrosion-resistant, and maintain a low interface contact electrical resistance (ICR). The root causes of the BPPs corrosion issues are non-conductive oxides formation increasing electrical resistance, and metal ions out-diffusion poisoning the catalyst and electrolyte membrane. The US Department of Energy has set targets for bipolar plates in fuel cells, including corrosion current densities < 1 μA/cm 2 and ICR < 10 mΩ·cm 2 . Even though these targets do not apply to BPPs in PEM electrolyzers, they provide an indication of acceptable values. The problems outlined above are being overcome or minimized by applying corrosion-resistant and simultaneously electrically conductive coatings. This work, therefore, investigates various corrosion-resistant and electrically conductive oxide coatings prepared by reactive high-power impulse magnetron sputtering (HiPIMS) on SS316L substrates. Reactive HiPIMS is an advanced and progressive magnetron sputter deposition technique suitable for preparing high-quality oxide coatings. The main advantage of HiPIMS is a high degree of ionization of sputtered particles in the discharge plasma and the associated high ion-to-atom ratio in particle flux toward the substrate. This allows one to achieve coating densification and crystallinity at low substrate temperature and without applying a substrate bias voltage. In our case, the native oxide on the SS316L substrate surface was removed by employing plasma etching prior to the coating deposition utilizing HiPIMS-generated ions accelerated towards the substrate by an applied bias voltage. The oxide coatings were deposited using an unbalanced magnetron with a directly water-cooled planar target with a diameter of 100 mm in argon-oxygen gas mixtures at the argon pressure of 1 Pa in an ultra-high vacuum chamber. The oxygen partial pressure was controlled by a PID regulator at a given power density in a pulse. This allowed the deposition of the coatings with different stoichiometries and, thus, different electrical conductivity and corrosion resistance. The electrical resistivity of oxide coatings was measured by a four-point probe system on a non-conductive glass substrate. The compaction pressure dependence of ICR between the test plate and a gas diffusion layer (GDL) was measured in a range from 0.3 to 2.0 MPa on a custom-designed device using gold-coated cylindrical copper electrodes. All electrochemical measurements were performed in an H 2 SO 4 electrolyte solution with an acidity of pH 5.5, fluorine ions concentration of 5 ppm, and a temperature of 60 °C to simulate the PEM electrolyzer environment. Accelerated corrosion tests were carried out in extreme anodic conditions of the PEM electrolyzer via potentiostatic polarization at a potential of 2 V vs SHE. Open circuit potential, corrosion current, Tafel slopes, and polarization resistance were determined from potentiodynamic polarization curves measured from 0 to 2 V vs SHE recorded at a scan rate of 1 mV/s, this range should cover most of the potentials experienced inside a PEM electrolyzer. Potentiodynamic polarization and ICR versus compaction pressure were measured before and after the accelerated corrosion test.

Preparation and Performance of Conductive Ti4O7 Coatings on SS316L Bipolar Plates

Thermal Sprayed Protective Coatings for Bipolar Plates of Hydrogen Fuel Cells and Water Electrolysis Cells

Investigation on the performance of Pt surface modified Ti bipolar plates in proton exchange membrane water electrolyzer

Corrosion Behavior and Conductivity of TiNb and TiNbN Coated Steel for Metallic Bipolar Plates

Role of Oxide Layer on Corrosion Resistance and Surface Conductivity of Titanium Bipolar Plates for Proton Exchange Membrane Fuel Cell

Corrosion behavior of TiC/amorphous carbon coated stainless steel as bipolar plate for proton exchange membrane fuel cell

Corrosion behavior of metallic coatings on titanium bipolar plates of proton exchange membrane water electrolysis

Corrosion Resistance, Interfacial Contact Resistance, and Hydrophobicity of 316L Stainless Steel Bipolar Plates Coated with TiN/Amorphous Carbon Double Layer under Different Carbon Target Currents

Corrosion-Resistant and Electrically Conductive Oxide Coatings for Metal Bipolar Plates for PEM Electrolyzers

Response characteristics of platinum coated titanium bipolar plates for proton exchange membrane water electrolysis under fluctuating conditions

Corrosion resistant and conductive TiN/TiAlN multilayer coating on 316L SS: a promising metallic bipolar plate for proton exchange membrane fuel cell

A Ti3C2Tx-carbon black-acrylic epoxy coating for 304SS bipolar plates with enhanced corrosion resistant and conductivity

Impact of Surface Pretreatment on the Corrosion Resistance and Adhesion of Thin Film Coating on SS316L Bipolar Plates for Proton-Exchange Membrane Fuel Cell Applications

Comparison of Magnetron-Sputtered and Cathodic Arc-Deposited Ti and Cr Thin Films on Stainless Steel for Bipolar Plates

Electrochemical properties and surface conductivity of Ti-Al coating on Ti-6Al-4V

Corrosion Resistance and Conductivity of Ta-Nb-N-Coated 316L Stainless Steel as Bipolar Plates for Proton Exchange Membrane Fuel Cells

Enhanced Corrosion Resistance and Interfacial Conductivity of TiCx/a-C Nanolayered Coatings Via Synergy of Substrate Bias Voltage for Bipolar Plates Applications in PEMFCs

Corrosion resistance and conductivity of amorphous carbon coated SS316L and TA2 bipolar plates in proton-exchange membrane fuel cells

Performance of Tantalum Modified 316L Stainless Steel Bipolar Plate for Proton Exchange Membrane Fuel Cell

Low-Cost Bipolar Plates of Ti4O7-Coated Ti for Water Electrolysis with Polymer Electrolyte Membranes

Enhanced Corrosion Resistance and Interfacial Conductivity of TiC x/a-C Nanolayered Coatings via Synergy of Substrate Bias Voltage for Bipolar Plates Applications in PEMFCs