Abstract:Abstract In the last years, additive manufacturing (AM) has turned into an emerging technology and an increasing number of classes of material powders are now available for this manufacturing process. For large-scale adoption, an accurate knowledge of the mechanical behaviour of the resulting materials is fundamental, also considering that reliable data are often lacking and dedicated standards are still missing for these AM alloys. In this regard, the aim of the present work is to characterize both the high-cycle-fatigue (HFC) and the low-cycle-fatigue (LCF) behaviour of AM 17–4 PH stainless steel (SS). To better understand the performance of the selected alloy, four series of cylindrical samples were manufactured. Three series were produced via selective laser melting (SLM), better known as laser-based powder bed fusion of metals technology using an EOS M280 machine. The first series was tested in the as-built condition, the second was machined before testing to obtain a better surface finishing, while the third series was post-processed via hot isostatic pressing (HIP). Finally, a fourth series of samples was produced from the wrought 17–4 PH material counterpart, for comparison. The understanding and assessment of the influence of surface finishing on the fatigue behaviour of AM materials are fundamental, considering that in most applications the AM parts may present reticular or lattice structures, internal cavities or complex geometries, which must be set into operation in the as-built conditions, since a surface finishing postprocess is not convenient or not feasible at all. On the other side, a HIP process is often suggested to reduce the internal porosities and, therefore, to improve the resulting mechanical properties. The high-cycle-fatigue limits were obtained with a short staircase approach according to the Dixon statistical method. The maximum number of cycles (run-out) was set equal to 50,00,000. The part of the Wöhler diagram relative to finite life was also characterized by means of additional tests at higher stress levels. On the other side, the low-cycle tests allowed to tune the Ramberg–Osgood cyclic curves and the Basquin–Coffin–Manson LCF curves. The results obtained for the four different series of specimens permitted to quantify the reduction of the mechanical performance due to the actual limits of the laser-based powder bed fusion technology (surface quality, internal porosity, different solidification) with respect to traditional manufacturing and could be used to improve design safety and reliability, granting structural integrity of actual applications under elastic and elasto-plastic fatigue loads.

Fatigue properties and S-N curve estimating of 316L stainless steel prepared by SLM

Fatigue behavior of selective laser melted 316L stainless steel: experiments and modeling

Analysis of Fatigue Properties of Selective Laser Melting 316L Stainless Workpiece After Post-heat Treatment

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Effects of low-cycle fatigue on static mechanical properties, microstructures and fracture behavior of 304 stainless steel

Microstructure and Fatigue Damage of 316L Stainless Steel Manufactured by Selective Laser Melting (SLM)

High Cycle Fatigue Behaviour of 316L Stainless Steel Produced via Selective Laser Melting Method and Post Processed by Hot Rotary Swaging

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods

A Novel Method for Early Fatigue Damage Diagnosis in 316L Stainless Steel Formed by Selective Laser Melting Technology

Dissipative and thermal aspects in cyclic loading of additive manufactured AISI 316L

High Cycle Fatigue Behavior of 316L Steel Fabricated by Laser Powder Bed Fusion: Effects of Surface Defect and Loading Mode

Fatigue behaviour of selective laser melting steel components

High and low-cycle-fatigue properties of 17–4 PH manufactured via selective laser melting in as-built, machined and hipped conditions

Effect of scanning speed on fatigue behavior of 316L stainless steel fabricated by laser powder bed fusion

Experimental Investigation and Numerical Modelling of the Cyclic Plasticity and Fatigue Behavior of Additively Manufactured 316L Stainless Steel

Fatigue inhomogeneity of thick 316L stainless steel joints fabricated by ultra-high power laser-MIG hybrid welding

Fatigue strength of additively manufactured 316L austenitic stainless steel

Fatigue Response of Additive-Manufactured 316L Stainless Steel