Abstract:The purpose of this study was to evaluate in vitro the effect of a phosphoric acid etchant containing benzalkonium chloride on the dentin/adhesive interface in primary teeth. The teeth had caries lesions involving enamel and dentin, and were stored in a 2% glutaraldehyde solution for 2-4 hours. The teeth were divided into five groups of five teeth each: Group 1: Etching for 15 seconds with a semigel 32% phosphoric acid containing benzalkonium chloride; Group 2: Etching with 35% phosphoric acid for 15 seconds; Group 3: Treated with a 2% benzalkonium chloride in a alcoholic solution; Group 4: Conditioned with a 3% benzalkonium chloride in a alcoholic solution (control group); Group 5: The teeth were untreated (control group). The carious tissue was removed with a carbide bur in high-speed and copious air water spray. The overall dimensions and depths of the cavities were determined by the carious tissue removal. After the caries lesion was removed, the cavity was cleaned with an air-water spray and the dentin was treated according to the specific group. The teeth were then restored with Scotchbond Multi-Purpose Plus (3M, St. Paul, MN) and Z-100 resin-based composite (3M, St. Paul, MN) according to the manufacturer's instructions. After the teeth were restored they were stored in water for 24 hours at room temperature and the restorations polished. After storage the teeth were thermally challenged for 500 cycles in temperatures of 50 C and 550 C and then stored in 100% humidity until the sectioning procedures. The teeth were cut into two sections along the longitudinal axis through the center of the teeth and passed the mesial-distal surfaces through the restoration by using a double-face diamond disc with water coolant. The specimens were ground with 320 up to 600 grit silicon carbide paper and polished with 6 mm and 1 mm diamond paste and 0.25 pm alumina solution. The specimens were etched with 10% citric acid for 1 minute and washed with deionized water. After that, they were deproteinized with 10% NaOCl for 5 seconds. The specimens were dried at room temperature sputter-coated with gold and observed with an SEM for assessment of the morphology of the bonded interface. The interface was observed to determine the presence/absence of hybrid layer formation, resin tags, and gaps. In the groups treated only with benzalkonium chloride solutions, spaces were observed in the resin/dentin interface. Similar findings were observed in the control group, which received no treatment on the dentin before primer application. In these groups neither resin tags or hybrid layer formation was observed. The presence of an amorphous layer, which was unremoved smear layer, was noted. The group treated with 35% phosphoric acid showed a hybrid layer formation (8.15 microns). This layer was linked intimately with the peritubular and intertubular dentin. Tags formation was observed towards the pulp under the hybrid layer. In these specimens the gaps were not observed between the dentin layer and bonding materials. The total removal of the smear layer was observed using 37% phosphoric acid with benzalkonium chloride. A hybrid layer (+/- 7.32 microns) and resin-tags attached to this layer were observed similar to the group in which the 35% phosphoric acid was used. The samples showed total removal of the smear layer and no gaps were observed in the dentin/adhesive interface.

Effect of phosphoric acid containing polyvinylpyrrolidone as protective etchant for dentin bonding

A polyhexamethylene biguanide-assembly assisted strategy of dentin bonding greatly promotes bonding effects and caries treatment

Selective demineralisation of dentine extrafibrillar minerals—A potential method to eliminate water-wet bonding in the etch-and-rinse technique

Reconstruction of a Demineralized Dentin Matrix Via Rapid Deposition of CaF2 Nanoparticles in Situ Promotes Dentin Bonding.

Effect of etching agent on dentinal adhesive interface in primary teeth

Effect of experimental dentin etchants on dentin bond strength, metalloproteinase inhibition, and antibiofilm activity

Effect of acid etching time and technique on interfacial characteristics of the adhesive-dentin bond using differential staining.

Do Phosphoric Acid Esters Affect the Immediate Enamel Bond Strengths?

Effects of Phosphoric Acid Pre-Etching on Chemisorption between Enamel and MDP-Containing Universal Adhesives: Chemical and Morphological Characterization, and Evaluation of Its Potential

Reactivation of inactivated endogenous proteolytic activities in phosphoric acid-etched dentine by etch-and-rinse adhesives

The Effect of Prime-and-rinse Approach Using MDP Micellar Solutions on Extrafibrillar Demineralization and Dentin Bond Performance.

Influence of Proanthocyanidins Combined with Ethanol-Wet Bonding on the Bonding Quality of Fibre Posts to Root Dentine.

Bonding Quality of Etch-and-Rinse Adhesives in Root Canals Upon Different Pretreatments.

Effect of Phytic Acid Etching and Airborne-Particle Abrasion Treatment on the Resin Bond Strength

Effects of lactic acid etching on immediate and aged bond strength of resin-dentin bonding interface

Comparison of dentin decalcification between polycarboxylic acids and phosphoric acid

Influence of collagen cross-linkers addition in phosphoric acid on dentin biomodification and bonding of an etch-and-rinse adhesive

Effect of an extrafibrillar dentin demineralization strategy on the durability of the resin–dentin bond

Effects of pretreatment in post space on the bonding strength of self-adhesive resin cement to fiber posts

Effect of different adhesive application approaches on bond strength in over-etched dentin

Effect of Etching Method and Time on Surface Roughness and Shear Bond Strength of a Novel Universal Adhesive to Ground Enamel