Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Modulating band alignment at the 3D metal/semiconductor interface of liquid metal-embraced semiconductor photoelectrodes for water splitting

Interface Engineering of Ta3N5 Thin Film Photoanode for Highly Efficient Photoelectrochemical Water Splitting

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Engineering Interfacial Band Bending over ZnIn 2 S 4 /SnS 2 by Interface Chemical Bond for Efficient Solar‐Driven Photoelectrochemical Water Splitting

Engineering Interfacial Band Bending over ZnIn2S4/SnS2 by Interface Chemical Bond for Efficient Solar‐Driven Photoelectrochemical Water Splitting (Adv. Energy Mater. 22/2022)

Interface Manipulation to Improve Plasmon‐Coupled Photoelectrochemical Water Splitting on Α‐fe2o3 Photoanodes

Metal@semiconductor Core-Shell Nanocrystals with Atomically Organized Interfaces for Efficient Hot Electron-Mediated Photocatalysis

WO3@α‐Fe2O3 Heterojunction Arrays with Improved Photoelectrochemical Behavior for Neutral Ph Water Splitting

Tuning the Carrier Transfer Behavior of Coaxial ZnO/ZnS/ZnIn2 S4 Nanorods with a Coherent Lattice Heterojunction Structure for Photoelectrochemical Water Oxidation

Modulating Interfacial Charge Transfer Behavior through the Construction of a Hetero-Interface for Efficient Photoelectrochemical Water Splitting

Interface Engineering for Modulation of Charge Carrier Behavior in ZnO Photoelectrochemical Water Splitting

Modulation of Hot Electrons Via Interface Engineering of Au@ZnIn2S4/MXene for Efficient Photoelectrochemical Seawater Splitting under Visible Light

Bifunctional photothermal effect to promote band bending and water oxidation kinetics for improving photoelectrochemical water splitting

Engineering band structure via dual atoms modification for the efficient photoanode

Metal–insulator–semiconductor photoelectrodes for enhanced photoelectrochemical water splitting

Fine tuning of charge motion over homogeneous transient metal chalcogenides heterostructured photoanodes for photoelectrochemical water splitting

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Interfacial Chemical Bond‐Modulated Z‐Scheme Charge Transfer for Efficient Photoelectrochemical Water Splitting

In situ fabrication of WO3/CuWO4/CuO heterojunction photoanode for boosted interfacial charge transfer and enhanced photoelectrochemical water splitting

Balancing Catalytic Activity and Interface Energetics of Electrocatalyst-Coated Photoanodes for Photoelectrochemical Water Splitting.

Interfacial [S─Cu─C] Bonds Induced π‐d Electron Coupling Toward Modulating Charge Transfer for Efficient Solar Water Oxidation