Abstract:A combined computational/experimental study is performed to investigate hypersonic low-density internal gas flows in a convergent-divergent nozzle over a wide range of Knudsen numbers. The numerical solutions are obtained using the direct simulation Monte Carlo (DSMC) method and the experimental measurement is conducted in the hypersonic low-density wind tunnel FengDong-19 (FD-19) at China Academy of Aerospace Aerodynamics. Rarefaction effects are found to play an important role in pressure disturbance propagation, flow separation (vortex formation), mass flow rate, velocity slip, and thermally nonequilibrium effect. Pressure disturbance propagates farther upstream with increasing free-stream Knudsen number Kn∞. Although there is no flow separation near the nozzle surface for Kn∞ = 0.1, the slip velocity is such anomalously small that it cannot suppress flow separation, thus, producing one small vortex for Kn∞ = 0.2, 0.5 and 1. Due to the presence of the continuous sheet of two-order Moffatt vortices, the skin friction coefficient does not change sign (positive to negative) in the small separated region. This indicates that the incipient and small separated flows with second-order vortices may not be discerned by examining the sign of the skin friction. As Kn∞ grows to 2, this small vortex disappears. However, with further increase in Kn∞, a large vortex nearly fills the compression section of the nozzle due to the backflow effect. As Kn∞ increases from continuum to free molecular regime, the dimensionless mass flow rate mfr/mfr∞ rises first to its maximum at Kn∞ ∼ 0.2 resulting from the weaker flow blockage effect. After the maximum point, mfr/mfr∞ dwindles first because of the stronger backflow effect and rises again to its free molecular limit, obtaining its minimum (the so-called Knudsen minimum) at Kn∞ ∼ 10. DSMC results and experimental data obtained from FD-19 wind tunnel are in good agreement, achieving a mutual validation between computation and experiment. This indicates that our experiment provides valuable data that can server as “benchmark” case to support computational code evaluation and validation.

Hypervelocity imperfect gas nozzle design with shared wave-elimination contour

Design and Optimization of Three-Dimensional Supersonic Asymmetric Truncated Nozzle

Design and Verification of Minimum Length Nozzles with Specific/Variable Heat Ratio Based on Method of Characteristics

Performances Analysis of Asymmetric Minimum Length Nozzles

Novel design of variable Mach number nozzle operated by a single jack

Design and analysis of the scramjet nozzle with contact discontinuity

Design Method with Controllable Velocity Direction at Throat for Inward-Turning Inlets

Experimental and Numerical Investigation of the Non-Reacting Flow in a High-Fidelity Heavy-Duty Gas Turbine DLN Combustor

A novel design method of variable geometry turbine nozzles for high expansion ratios

Numerical Study on the Effect of a Lobed Nozzle on the Flow Characteristics of Submerged Exhaust

Structure Design and Performance Investigation of a Novel Rotatable Vane Nozzle

Analysis of the internal flow features of a CO2 transonic nozzle and optimization of the nozzle shape profile

A New Design Method of Single Expansion Ramp Nozzles under Geometric Constraints for Scramjets

Structure optimization of submerged water jet cavitating nozzle with a hybrid algorithm

Design and aerodynamic characteristics of variable-geometry hypersonic inlet based on shock wave elimination

Numerical and Experimental Investigation of Rarefied Hypersonic Flow in a Nozzle

Experimental investigation of internal and external flow fields of jetting nozzles with different structures

Design and flow analysis of laser cutting supersonic nozzles

Analysis and Manipulation of the Separation Zone in an Overexpanded Combined Exhaust Nozzle

Improved Design Method for Hypersonic Intakes Using Pressure-Corrected Osculating Axisymmetric Flows Method

Quantitative Analysis of the Minor Deviations in Nozzle Internal Geometry Effect on the Cavitating Flow