Abstract:Patients with stroke and other neurological disorders like trauma, multiple sclerosis (MS) experience different lower limb disabilities due to various damages in neuromuscular system. Orthotic devices are prescribed to compensate muscle weakness, prevent unwanted movement of the impaired limb. Design and manufacturing methods of lower limb orthoses involve manual techniques e.g. casting and moulding of the limbs to be treated, vacuum forming etc. Such methods are time consuming, require skilful labour and often based on trial and error rather than systematic engineering and evidence based principles. In recent years, 3D scanning and reconstruction of medical images facilitate making 3D computer models of lower limb, which allows computer aided design (CAD) tools to be incorporated in orthotic design. All these approaches rely on the external model of lower limb and limited to single piece plastic ankle foot orthosis (AFO) only. To design orthosis with articulated joint, precise alignment of anatomical joint and mechanical axis is necessary. However, it is difficult to infer joint axes from external models as it is partially specified by skeletal structure. In our research, a design approach for custom knee ankle foot orthosis and ankle foot orthosis with commercially available joints has been demonstrated, which involves skeletal structure of lower limb for locating anatomical axes to ensure accurate alignment of orthotic mechanical joint. CAD models of the orthotic components were developed based on the 3D models of a healthy subject’s lower limb, which were developed through 3D reconstruction. Components of the orthotics were fabricated by rapid prototyping and machining to demonstrate the new approach. The fabricated orthoses were evaluated by a certified orthotist and the performance of the custom made AFO was compared statistically with a pre-fabricated AFO with similar ankle joint. The manufacturing process requires approximately 50% lesser time to develop AFO and 70% lesser time to develop KAFO compared to Brace and Limb laboratory of University Malaya. Unlike traditional approaches, the design technique facilitates exact positioning of articulated joint. The developed orthoses are light in weight, comfortable and easy to don and doff. Biomechanical test implies that the fabricated AFO provides better range of motion than a pre-fabricated AFO with same ankle joint. Although the custom AFO allowed significantly higher plantar flexion during pre-swing compared to pre-fabricated AFO condition (MD = 1.734, MSD = 1.55), the subject’s ankle required to generate significantly higher power with the pre-fabricated AFO (MD = 0.141, MSD = 0.035). These findings suggest that the subject had to overcome higher resistance with pre-fabricated AFO compared to custom made AFO. Simultaneous viewing of exterior and skeletal geometry might help the clinicians modify the design to enhance performance of the orthotic device.

Application of multi-criteria decision-making methods in the selection of additive manufacturing materials for solid ankle foot orthoses

Process Planning for the Fuse Deposition Modeling of Ankle-Foot-Othoses

Assessment of consolidative multi-criteria decision making (C-MCDM) algorithms for optimal mapping of polymer materials in additive manufacturing: A case study of orthotic application

Multiple-Criteria Decision-Making and Sensitivity Analysis for Selection of Materials for Knee Implant Femoral Component

Material Performance Evaluation for Customized Orthoses: Compression, Flexural, and Tensile Tests Combined with Finite Element Analysis

A reasonable approach to determine structural dimension of FDM fabricated orthopedic orthosis using finite element simulation and simple additive weighting method

Multidisciplinary topology and material optimization approach for developing patient-specific limb orthosis using 3D printing

An Insight into the Characteristics of 3D Printed Polymer Materials for Orthoses Applications: Experimental Study

Predicting Mechanical Properties of Polymer Materials Using Rate-Dependent Material Models: Finite Element Analysis of Bespoke Upper Limb Orthoses

Study of selected properties of PLA used in 3D printing

Selection of sustainable material for the manufacturing of complex automotive products using a new hybrid Goal Programming Model for Best Worst Method–Proximity Indexed Value method

Innovative Approaches to 3D Printing of PA12 Forearm Orthoses: A Comprehensive Analysis of Mechanical Properties and Production Efficiency

COMPUTER AIDED DESIGN AND FABRICATION OF A CUSTOM ARTICULATED ANKLE FOOT ORTHOSIS

Multi-Attribute Decision Making: Parametric Optimization and Modeling of the FDM Manufacturing Process Using PLA/Wood Biocomposites

Comparative Analysis of Impact Strength among Various Polymeric Materials for Orthotic Production

Lightweight design of Knee-Ankle-Foot Orthotic Devices using Voronoi patterns for Additive Manufacturing

Integrated product-process design: Material and manufacturing process selection for additive manufacturing using multi-criteria decision making

Optimization of Fused Deposition Modelling Acrylonitrile-co-Butadiene-co-Styrene Parameters using ANOVA and Hybrid GRA–TOPSIS

Design of an Orthopedic Product by Using Additive Manufacturing Technology: The Arm Splint

Computer integrated design and manufacturing of patient specific lower limb orthoses through 3D reconstruction / Morshed Alam

Multi objective optimization of 3D printing process using multi-attribute decision making methods