Abstract:Poly(L-lactide) (PLLA) has been receiving attention as a material for bone fixation devices because of its good biocompatibility and biodegradability. However, its mechanical properties are weaker than those of natural bone. Interestingly, solid-state extrusion can enhance the mechanical properties by orienting the polymer chains, and molecular weight is one of the key factors in this process. In this study, we optimized the heating conditions for vacuum compression molding to make a PLLA block for the solid-state extrusion process. We confirmed that the molecular weight of the material decreased with increasing heating temperature and time. In the case of a low molecular weight such as 120 kDa, the heating temperature and time were optimized to 190 oC and 90 min, respectively. Moreover, we fabricated a plate, a rod, and a square pole of PLLA by solid-state extrusion for the development of a bone plate, a screw, and an interbody cage. PLLA plates having various molecular weights (150-250 kDa) were extruded to various draw ratios to investigate the effect of molecular weight on the solid-state extrusion process. The mechanical properties such as flexure stress and flexure modulus increased with increasing draw ratio, which in turn increased with increasing molecular weight of the polymer. In addition, we determined that the crystallinity of PLLA dramatically increased when the draw ratio was more than 4. In addition, the orientation of the crystals by solid-state extrusion was confirmed by using X-ray diffraction, and the orientation effect increased with increasing draw ratio of the extruded PLLA. PLLA plates made by solid-state extrusion could be manufactured into bone plates. Furthermore, we fabricated a PLLA rod by solid-state extrusion and vacuum compression molding. The flexural properties of the extruded rod were better than those of the molded rod. We could, therefore, fabricate a screw using the extruded PLLA rod. Finally, interbody cages were made by using poly(L,D/L-lactide) (PLDLLA), PLLA of various molecular weights (150-250 kDa), and PLLA enhanced by solid-state extrusion. The results of the compression tests indicated that PLLA was generally stronger than PLDLLA and that the extruded PLLA had the best mechanical properties. Consequently, it is possible to successfully manufacture biodegradable spinal fixation devices, including plates, screws, and interbody cages, by solidstate extrusion. Moreover, their mechanical properties could be improved by increasing the draw ratio and molecular weight.

Enhancement of the mechanical properties of polylactides by solid-state extrusion. I. Poly(D-lactide)

Enhancement of the mechanical properties of polylactides by solid-state extrusion. II. Poly(L-lactide), poly(L/D-lactide), and poly(L/DL-lactide

On the enhancement of thermo-mechanical properties of poly(L-lactide) by solid-state extrusion for biodegradable spinal fixation devices

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Effects of extrusion draw ratio on the morphology, structure and mechanical properties of poly(L-lactic acid) fabricated using solid state ram extrusion

Development of Oriented Morphology and Mechanical Properties upon Drawing of Stereo-Complex of Poly(L-lactic acid) and Poly(D-lactic acid) by Solid-State Coextrusion

Mechanical properties of melt-fabricated, drawn films of A–B–A triblock copolymers of poly(l-lactide) (A) and two types of polyethers (B)

Melt strengthening of poly (lactic acid) through reactive extrusion with epoxy-functionalized chains

A New Generation of Poly(lactide/ε-Caprolactone) Polymeric Biomaterials for Application in the Medical Field.

Short Poly(ethylene Glycol) Block Initiation of Poly(l‐lactide) Di‐block Copolymers: a Strategy for Tuning the Degradation of Resorbable Devices

Long chain branching polylactide: Structures and properties

Preparation and Characterization of High-Melt-Strength Polylactide with Long-Chain Branched Structure Through Γ-Radiation-induced Chemical Reactions

Tuning the Rheological, Thermal, and Solid-State Properties of Branched PLA by Free-Radical-Mediated Reactive Extrusion

Mechanical Behaviour of Polylactic Acid Parts Fabricated via Material Extrusion Process: A Taguchi-Grey Relational Analysis Approach

Study on the Extrusion Molding Process of Polylactic Acid Micro Tubes for Biodegradable Vascular Stents

An insight into enhancing the physical properties of poly(lactic acid) (D600) fibers

Effects of the Manufacturing Methods on the Mechanical Properties of a Medical-Grade Copolymer Poly(L-lactide-co-D,L-lactide) and Poly(L-lactide-co-ε-caprolactone) Blend

Ductile and biodegradable poly (lactic acid) matrix film with layered structure

Regulating mechanical performance of poly (l-lactide acid) stent by the combined effects of heat and aqueous media

Crystallinity and Property Enhancements in Neat Polylactic Acid by Chilled Extrusion: Solid‐State Shear Pulverization and Solid‐State/Melt Extrusion