Abstract:Melt-crystallized, low molecular weight poly(L-lactic acid) (PLLA) consisting of a crystals was uniaxially drawn by solid-state extrusion at an extrusion temperature (T ext ) of 130-170 °C. A series of extrusion-drawn samples were prepared at an optimum T ext value of 170 °C, slightly below the melting temperature (T m ) of a crystals (∼180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide-angle X-ray scattering (WAXD), and small-angle X-ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid-state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of a and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010) α and (003) β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial a form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid-state extrusion of melt-crystallized, low molecular weight PLLA slightly below T m . The structure and properties of the α- and β-form crystals were also studied.

Development of Oriented Morphology and Mechanical Properties upon Drawing of Stereo-Complex of Poly(L-lactic acid) and Poly(D-lactic acid) by Solid-State Coextrusion

Competing Stereocomplexation and Homocrystallization of Poly(l-lactic Acid)/poly(d-Lactic Acid) Racemic Mixture: Effects of Miscible Blending with Other Polymers

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Combined Processing of Polypropylene Film by Coextrusion and Zone‐annealing

Enhanced Crystallization Rate and Mechanical Properties of Poly(l‐lactic Acid) by Stereocomplexation with Four‐armed Poly(ϵ‐caprolactone)‐block‐poly(d‐lactic Acid) Diblock Copolymer

Structure Evolution of Oriented Poly( l -lactic acid) Ultrathin Films during Deformation

Structure evolution of amorphous poly(d-lactic acid) on highly oriented poly(l-lactic acid) film during annealing

Mechanical properties of melt-fabricated, drawn films of A–B–A triblock copolymers of poly(l-lactide) (A) and two types of polyethers (B)

Enhancement of the mechanical properties of polylactides by solid-state extrusion. II. Poly(L-lactide), poly(L/D-lactide), and poly(L/DL-lactide

Exclusive Stereocomplex Crystallization of Linear and Multiarm Star-Shaped High-Molecular-Weight Stereo Diblock Poly(lactic acid)s.

Construction of fully biodegradable poly(L-lactic acid)/poly(D-lactic acid)-poly(lactide-co-caprolactone) block polymer films: Viscoelasticity, processability and flexibility

Promoting the formation of stereocomplex crystal in PLLA/PDLA by crosslinking restricted phase separation and solid-state stretching induced orientation

Effects of extrusion draw ratio on the morphology, structure and mechanical properties of poly(L-lactic acid) fabricated using solid state ram extrusion

Multiscale Structural Evolutions and Deformation Mechanisms of Stereocomplexed and Homocrystalline Poly(lactic acid)s during Stretching: Correlating Thermomechanical Properties with Polymorphic Structures

Transparent, Heat-Resistant, Ductile, and Self-Reinforced Polylactide through Simultaneous Formation of Nanocrystals and an Oriented Amorphous Phase

Facile and efficient formation of stereocomplex polylactide fibers drawn at low temperatures

Crystallization and Mechanical Propertiesof Poly (D, L) Lactide-based Blown Films

Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Two-Stage Crystallization Kinetics and Morphological Evolution with Stereocomplex Crystallite-Induced Enhancement for Long-Chain Branched Polylactide/Poly(D-lactic Acid) Blends

Toward Exclusive Stereocomplex Crystallization of High-Molecular-weight Poly(l-Lactic Acid)/poly(d-Lactic Acid) Blends with Outstanding Heat Resistance Via Incorporating Selective Nucleating Agents.

Scalable Preparation of Complete Stereo-Complexation Polylactic Acid Fiber and Its Hydrolysis Resistance