Abstract:Adding stereocomplex (SC) crystals into matrix can effectively improve the hydrolysis resistance and heat-resistance of polylactic acid (PLA). However, the existence of pre-formed SC crystals will increase the processing difficulty because a higher processing temperature is needed. Thus the exploration of inducing SC crystals via external force fields is important. In this paper, 'quenched' and 'annealed' PLA enantiomer mixtures were studied. The enantiomer mixtures were prepared by solution coprecipitation. Preparation of the 'quenched' specimen is done in two steps: hot pressed at 250 degrees C for 5 min and then quenched in air (15 degrees C). The method of annealing is done as following: hot pressed at 250 degrees C for 5 min, annealed at 200 degrees C for 30 min, and finally quenched in air. The X-ray diffraction patterns indicated that a loose structure with low order degree, named as quasi-ordered phase (QOP), was formed in the two types of the samples. Based on this structure, SC crystals was formed during stretching near the glass transition temperature (T-g) of PLA. The results of infrared spectra indicated that adequate amount of poly(D-lactic acid) (PDLA) is the prerequisite for the induction of SC crystals. There was no SC crystal generated in the specimens with 5% of PDLA, regardless of the treatment used. However, SC crystal appearred in the specimens with 20% of PDLA. This is because that adequate amount of QOP regions can merge and rebuild into complete crystals. In the specimens of high PDLA content, the transition could happen either during annealing or stretching above Tg (e.g., 70 degrees C). Owing to the self-nucleation and heterogeneous nucleation of QOP, alpha'-form crystal would be formed concomitantly during annealling. Therefore the former approach cannot generate pure SC crystal. As to the latter approach, depending on the tensile temperature and rate, mesophase, SC crystal and alpha'-form can be selectively generated. When stretched below Tg (e.g., 50 degrees C), only mesophase can be obtained beacause of low chain activity. As stretched at 70 degrees C, the tensile model has a great effect on the induced results. Fast stretching will induce highly pure SC crystals. Otherwise, when given sufficent time for chain segmet adjustment, both SC and alpha'-form crystals would be induced.

Structure evolution of amorphous poly(d-lactic acid) on highly oriented poly(l-lactic acid) film during annealing

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Fractionated Crystallization Kinetics and Polymorphic Homocrystalline Structure of Poly(L-lactic Acid)/poly(d-Lactic Acid) Blends: Effect of Blend Ratio

Polymorphic Transition in Disordered Poly(l-lactide) Crystals Induced by Annealing at Elevated Temperatures

Structure Evolution of Oriented Poly( l -lactic acid) Ultrathin Films during Deformation

Rheology and Crystallization Behavior of Asymmetric Plla/Pdla Blends Based on Linear Plla and Pdla with Different Structures

Oriented Overgrowths Of Poly(L-Lactide) On Oriented Isotactic Polypropylene: A Sequence Of Soft And Hard Epitaxies

Lamella Reorientation in Thin Films of a Symmetric Poly(l-Lactic Acid)-Block-polystyrene Upon Crystallization at Different Temperatures

Promoting the formation of stereocomplex crystal in PLLA/PDLA by crosslinking restricted phase separation and solid-state stretching induced orientation

Studies on the Induction of Poly(lactic acid) Stereocomplex by Thermal and Tensile Treating

Introduction of Stereocomplex Crystallites of PLA for the Solid and Microcellular Poly(lactide)/poly(butylene Adipate-Co-terephthalate) Blends

Formation, structure and promoting crystallization capacity of stereocomplex crystallite network in the poly(lactide) blends based on linear PLLA and PDLA with different structures

Crystal Structure and Morphology Influenced by Shear Effect of Poly(L-Lactide) and Its Melting Behavior Revealed by Waxd, Dsc and In-Situ Pom

Direct Investigations on Strain-Induced Cold Crystallization Behavior and Structure Evolutions in Amorphous Poly(lactic Acid) with SAXS and WAXS Measurements

Polymorphic Crystalline Structure and Crystal Morphology of Enantiomeric Poly(Lactic Acid) Blends Tailored by A Self-Assemblable Aryl Amide Nucleator

Controlling stereocomplex crystal morphology in poly(lactide) through chain alignment

Formation of Stereocomplex Crystal and Its Effect on the Morphology and Property of PDLA/PLLA Blends

Morphologies and Structures in Poly(L-Lactide-B-Ethylene Oxide) Copolymers Determined by Crystallization, Microphase Separation, and Vitrification

Unique Homo-Crystallization and Melting Behavior of Poly(L-lactic Acid): Influence of Stereocomplex with Varied Structure

Two-Stage Crystallization Kinetics and Morphological Evolution with Stereocomplex Crystallite-Induced Enhancement for Long-Chain Branched Polylactide/Poly(D-lactic Acid) Blends

Early Stage Interplay of Microphase Separation and Crystallization in Crystalline−Coil Poly(l-lactic Acid)-Block-polystyrene Thin Films