Abstract:PurposeAccurate 2D profile measurements at submillimeter precision are necessary for proton beam commissioning and periodic quality assurance (QA) purposes and are currently performed at our institution with a commercial scintillation detector (Lynx PT) with limited means for independent checks. The purpose of this work is to create an independent dosimetry system consisting of an in-house optical scanner and a BaFBrI:Eu2+ storage phosphor dosimeter by: (a) determining the optimal settings for the optical scanner, (b) measuring 2D proton spot profiles with the storage phosphors and (c) comparing them to similar measurements using a commercial scintillation detector. MethodsAn in-house two-dimensional (2D) laboratory optical scanner was constructed and spatially calibrated for accurate 2D photostimulated luminescence (PSL) dosimetry. Square 5 x 5 cm2 BaFBrI:Eu2+ dosimeter samples were uniformly irradiated with line scans performed to determine the physical and electronic scanner settings resulting in the highest signal-to-noise ratios (SNR) at a sub-millimeter spatial resolution. The resultant spatial resolution of the scanner was then quantitatively assessed by measuring (a) line pairs on a standard x-ray lead bar phantom and (b) modulation transfer functions. Following this, 2D proton spot profiles from a Mevion S250i Hyperscan proton unit were obtained at 1, 10, 20, 30, 40 and 50 monitor unit (MU) settings at maximum energy (E0 = 227.1 MeV) and compared to baseline profiles from a commercial scintillation detector, where 1 MU is calibrated to deliver 1 Gy absolute proton dose-to-water under reference conditions, i.e. 41 × 41 proton spots uniformly spaced by 0.25 cm within a 10 × 10 cm2 square field size at maximum energy (227.1 MeV) in water at depth of 5 cm at isocenter. The dosimetric system's sensitivities to (a) ±1 mm positional shifts and (b) ±0.3 mm beam lateral spread changes were quantitatively evaluated through a Gaussian fitting of the crossline and inline plots of the respective artificially shifted beam profiles. ResultsThe physical scanner settings of (a) Δτ = 27 ms time interval between data samples, (b) vx = 1.235 cm/s scanning speed, (c) 1% laser transmission (0.02 mW power) and (d) (Δx, Δy) = (0.33 mm, 0.50 mm) pixel sizes with electronic settings of (a) 300 microseconds time constant, (b) normal dynamic reserve, (c) 24 dB/oct low pass filter slope and (d) 160 Hz chopping frequency resulted in the highest SNR while maintaining sub-millimeter spatial resolution. The BaFBr0.85I0.15:Eu2+ storage phosphor dosimeters were linear from 1 – 50 MU and their profiles did not saturate up to 150 MU. The scanner was able to detect lateral displacements of ±1 mm in both the crossline and inline directions and ±0.3 mm beam spread changes that were artificially introduced by varying the incident proton energy. Specific to our proton unit, proton energy changes of ±1 MeV can also be detected indirectly via beam spread measurements. ConclusionOur combined dosimetric system including an in-house laboratory optical scanner and reusable BaFBr0.85I0.15:Eu2+ storage phosphors demonstrated a sufficient spatial resolution and dosimetric accuracy to support its use as an independent proton spot measurement dosimeter system. Its wide dynamic range allows for other versatile applications such as proton halo measurements.

Development of a Technique for Determining the Optimal Number of Projections when Realizing the Method of Multiangle Scanning of an Ionizing Radiation Beam

Determination of the optimal number of detectors for the multiangle wire beam scanning method

Measurement of the electron beam profile by the multiangle scanning method

Study on Optimizing Scan Parameter of Industrial CT Detection with Different Intensity Ray Sources

Optimization of Image Quality and Acquisition Time for Lab-Based X-ray Microtomography Using an Iterative Reconstruction Algorithm

Determination of virtual source position using back projecting zero and convergent arcTAN method for scanning-passive scatter beam in carbon ion therapy

High Energy Electron Radiography System Design and Simulation Study of Beam Angle-Position Correlation and Aperture Effect on the Images

A scatter correction method for Multi-MeV Flash Radiography

Angular correction methodology and characterization of a high-resolution CMOS array for patient specific quality assurance on a robotic arm linac

Construction of a radiation beam scanner and investigation of volume averaging correction factor effects on beam-profile

Beam Position Projection Algorithms in Proton Pencil Beam Scanning

Impact of Measurement Conditions and Design Features of IBA Detectors on the Small Radiation Fields Output Factors

Development of a storage phosphor imaging system for proton pencil beam spot profile determination

Dose-Area Product Determination and Beam Monitor Calibration for the Fixed Beam of the Shanghai Advanced Proton Therapy Facility

Fundamental radiological and geometric performance of two types of proton beam modulated discrete scanning systems

SU-DD-A4-05: Development of a Tetrahedron Beam Computed Tomography Benchtop System with a 75 Pixel Field Emission X-Ray Tube: Collimator Design and Image Reconstruction

Performance of a Scintillation Imaging System for Relative Dosimetry in Pencil Beam Scanning Proton Therapy

X-Ray Projection Simulation Based on Physical Imaging Model

Numerical optimization of longitudinal collimator geometry for novel x-ray field

Application and Development of a Method to Shim the Isochronous Field in Small Cyclotrons

Simulation study of electron beam optics for a distributed X-ray source toward stationary CT architecture