Abstract:Recycling lithium-ion battery materials is a crucial step to achieving a circular economy. A hydrometallurgical recycling process of spent lithium-ion battery materials involves leaching by acids and precipitation by bases. A large amount of Li 2 SO 4 leachate solution is generated at the end of the recycling process. Such Li 2 SO 4 solution can be separated by electrodialysis (ED) to form H 2 SO 4 and LiOH solutions, which are reused for leaching and precipitation, respectively, making the recycling a closed-loop process. In this study, an ‘electrodialysis stack constructed with bipolar membranes’ (EDBM) is built with repetitive unit cells consisting of a bipolar membrane, anion exchange membrane (AEM), and cation exchange membrane (CEM), see Fig. 1(a). The effective area for each membrane is 121.8 cm 2 (70mm×174mm). The gap between these membranes is 0.8mm, with a mesh inserted to allow flow mixing. All experiments were operated at constant current mode. The feed, acid, and base solutions were recirculated through their tanks at initial concentrations of 1.1, 0.1, and 0.1 mol/L. The ion concentrations of the solutions were measured with Inductively coupled plasma mass spectrometry periodically. The weight and the pH value of the solution tanks were also recorded. The trend of concentration variations of the present stack with up to 6 cell pairs is found to be consistent with that observed with a three-compartment configuration in our previous study [1]. The concentration of H 2 SO 4 increases with time linearly, whereas that of LiOH levels off due to a significant electro-osmosis that drags water through the CEM into the concentrate channel. The present setup differs from the three-compartment design in the bipolar membrane, which splits water to produce H + and OH - at the internal interface, eliminating the formation of bubbly flows in the unit cell. It is found that the voltage loss across the bipolar membrane ca. 1V accounts for a major part of the unit cell of about 1.27V. The effects of current density, number of cell pairs, and flow rates on the overall stack performance are investigated. Increasing the stack current density accelerates the separation process at the cost of higher voltage losses. It is found that increasing the number of cell pairs can improve the overall production efficiency and reduce energy consumption per cell pair. For instance, at 800 A/m 2 , the specific energy consumption for LiOH production is reduced to 3.40 kWh/kg with five cell pairs versus 5.83 kWh/kg with two cell pairs. It is also found that increasing the solution flow rate can result into the increase of LiOH solution concentration, ion recovery rate, and current efficiency (Fig. 1b), although the impact of flow rate is low. A small EDBM stack is constructed and tested for Li 2 SO 4 separation in the present study. This work demonstrates that EDBM can be a simple and energy-saving alternative to the current chemical precipitation method to produce LiOH from Li 2 SO 4 . The present study provides new insights into optimal operation and design for Li 2 SO 4 EDBM. The findings are helpful in determining how the stack can be scaled up for practical application. Furthermore, a 2D multiphysics model is currently under development to elucidate the coupled transport processes within the unit cell. The model will be validated with experimental data of the present setup. Figure 1

One‐step conversion of sulfate lithium into high‐purity lithium hydroxide crystals via bipolar membrane crystallization

Production of Lithium Hydroxide by Electrodialysis with Bipolar Membranes

Recovery of Acid and Base from Sodium Sulfate Containing Lithium Carbonate Using Bipolar Membrane Electrodialysis

Bipolar membrane crystallization enables near zero-waste production of high-purity oxalic acid crystals

Bipolar membrane capacitive deionization for the selective capture of lithium ions from brines and conversion to lithium hydroxide

Recycling Lithium from Waste Lithium Bromide to Produce Lithium Hydroxide

In-Situ Combination of Bipolar Membrane Electrodialysis with Monovalent Selective Anion-Exchange Membrane for the Valorization of Mixed Salts into Relatively High-Purity Monoprotic and Diprotic Acids.

Analysis of a Process for Producing Battery Grade Lithium Hydroxide by Membrane Electrodialysis

A novel process for multi-stage continuous selective leaching of lithium from industrial-grade complicated lithium-ion battery waste

A Green and Economical Method for Preparing Lithium Hydroxide from Lithium Phosphate

Optimizing Operational Parameters for Lithium Hydroxide Production via Bipolar Membrane Electrodialysis

An integrated membrane process for preparation of lithium hydroxide from high Mg/Li ratio salt lake brine

Production of Lithium Hydroxide from Lake Brines Through Electro–Electrodialysis with Bipolar Membranes (EEDBM)

Electrodialysis of Lithium Sulfate Solutions from Hydrometallurgical Recycling of Spent Lithium-Ion Batteries

Selective lithium recovery and integrated preparation of high-purity lithium hydroxide products from spent lithium-ion batteries

Preparation of LiOH through BMED process from lithium-containing solutions: Effects of coexisting ions and competition between Na+ and Li+

Bipolar Membrane Electrodialysis for Clean Production of L‐10‐camphorsulfonic Acid: from Laboratory to Industrialization

Electrochemical recovery lithium from brine via taming surface wettability of regeneration spent batteries cathode materials

Sustainable and efficient recovery of lithium from sodium sulfate by-product of lithium hydroxide production process using solvent extraction

Extracting Lithium from Low Concentration Solutions for Direct Battery Cathode Production