Abstract:High specific strength and superior corrosion resistance are two key characteristics of the aerospace grade AA7075-T6 alloy. However, the surface behavior of AA7075-T6 is found to be deprived, because of its behavior of being prone to fretting fatigue and adhesive wear under dry sliding conditions. Thus, surface wear behavior improvement with the retention of the microhardness of the alloy is required for increasing its wider application. For this, surface isomorphous precipitates and the soft matrix need to be protected through dispersion of hard thermally stable ceramic SiC with solid-lubricant graphite particles. The dispersion through friction stir processing (FSP) avoids detrimental phase formations by processing the metal alloy below its melting point temperature. Thus, dispersion of SiC-Graphite inside the AA7075-T6 using FSP is the focal point of the study. The low and high wear rate samples have been analyzed using SEM imaging and elemental analysis through XRD and EDS mapping. In this study, reinforcing the SiC-Gr particles greatly improved the wear behavior of the AA7075 alloy. Wear resistance has been controlled by combining soft solid lubricant Gr particles with load-bearing hard SiC nanoparticles. In dry sliding action, the base alloy matrix was severely exposed to wear, but the hard SiC nanoparticles served as load-bearing asperities and improved the wear resistance. Simultaneously, the graphite layers generated the soft solid lubricating tribofilm further to reduce the wear and friction between mating surfaces. The wear mechanisms have changed prominently from adhesion to abrasion and delamination through reinforcing the SiC-Gr reinforcements. The graphite content in a hybrid ratio with SiC hard particles was found to have improved the wear resistance by 78%. The tendency of fatigue was more effectively improved in surface composites as compared to the base alloy.

Understanding the tribo-corrosion mechanisms of friction stir processed steel deposited by high-pressure deposition additive manufacturing process

Friction Stir Processing on the Tribological, Corrosion, and Erosion Properties of Steel: A Review

A new method for localization of the residual stress distribution and enhancement of wear resistance through underwater friction stir processing with stationary shoulder

Friction Stir Processing of Cold-Sprayed High-Entropy Alloy Particles Reinforced Aluminum Matrix Composites: Corrosion and Wear Properties

Realizing the tribological feasibility of novel laser surface texturing techniques for cold spray kinetically metallized stainless steel

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

A study on microstructural, mechanical properties, and optimization of wear behaviour of friction stir processed AZ31/TiC composites using response surface methodology

Modification of Microstructure and Properties of Cold-Sprayed AlSi10Mg+TiB2 Composite by Friction Stir Process

Synergistic Effect Between Cavitation Erosion and Corrosion for Friction Stir Processed Mg-Zn Alloy

Assessing the tribo-corrosion resistance of surface nanostructured stainless-steel

Wear and Mechanical Behaviour of Magnesium AZ31 alloy Reinforced with MoS2 through Friction Stir Processing for Aerospace Applications

Advancements in Aluminum-Based Composite Manufacturing: Leveraging ZrO2 Reinforcement through Friction Stir Process

Revealing the fretting corrosion mechanisms of laser shock peened cold spray 316 L stainless steel

Microstructural mechanical and corrosion properties of SS304/HEA surface layer produced by Friction Stir Processing

Experimental Investigation into the Dry Reciprocating Wear Behavior of Additively Manufactured Austenitic Stainless Steel (316L) Alloys

Enhancing wear resistance of AZ61 alloy through friction stir processing: experimental study and prediction model

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

The effect of friction stir processing on mechanical, wear and corrosion characteristics of Cu-AlN-BN surface composite

A study on microstructural, mechanical properties and optimization of wear behavior of friction stir processed AlCrCoFeNi High Entropy Alloy reinforced SS410 using response surface methodology

Fatigue strength improvement due to alloying steel weld toes with WC tool constituent elements through friction stir processing

Evaluation of Microstructural, Mechanical and Corrosion Behaviours of Laminated AA6061/AA7075 Metal Matrix Composites Build by Friction Stir Additive Manufacturing for Structural Applications