Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

STUDI DESAIN SEL BAHAN BAKAR THORIUM NITRIDE (ThN) PADA GAS-COOLED FAST REACTOR

Neutronic Analysis of Thorium Nitride (Th, U233)N Fuel for 500MWth Gas Cooled Fast Reactor (GFR) Long Life without Refueling

Neutronic Design of Uranium-Plutonium Nitride Fuel-Based Gas-Cooled Fast Reactor (GFR)

Analisis Desain Teras Gas-Cooled Fast Reactor (GFR) Berpendingin S-CO2 Berbahan Bakar Uranium Nitrit dengan Minor Aktinida

Comparison of uranium plutonium nitride (U‐Pu‐N) and thorium nitride (Th‐N) fuel for 500 MWth gas‐cooled fast reactor (GFR) long life without refueling

Reviu Implementasi Thorcon Molten Salt Reactor di Indonesia

Neutron radiation characteristics of the IVth generation reactor spent fuel

Design study of gas-cooled fast reactor with natural uranium as fuel employing modified CANDLE shuffling strategy in the axial direction

STUDI PARAMETER DESAIN TERAS INTEGRAL PRESSURIZED WATER REACTOR DENGAN BAHAN BAKAR MIXED OXIDE FUEL MENGGUNAKAN PROGRAM SRAC

Analisis Burn Up Modified Candle Pada Gas Cooled Fast Reactor (Gcfr) Dengan Bahan Bakar Uranium Oksida

ANALYSIS OF CORE CONFIGURATION FOR CONCEPTUAL GAS COOLED FAST REACTOR (GFR) USING OPENMC

Possibility assessment for production of non-traditional nuclear fuel in thorium blanket of hybrid thermonuclear reactor

Power Flattening Study of Ultra-Long Cycle Fast Reactor Using Thorium Fuel

Preliminary Design of A Solid Particulate Cooled Blanket for the Steady-State Tokamak Reactor (Sstr)

Physical aspects for involvement of thermonuclear reactors into nuclear power systems

Comparison of the neutronic properties of the (Th- 233 U)O 2 , (Th- 233 U)C, and (Th- 233 U)N fuels in small long-life PWR cores with 300, 400, and 500 MW th of power

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

DESAIN OPTIMAL TERAS SMALL MODULAR MOLTEN SALT REACTOR (SM-MSR) SEBAGAI SISTROPULSI KAPAL PERANG EM P

URANIUM AND THORIUM POTENTIAL FOR INDONESIA'S FUTURE ENERGY SECURITY

Neutronic optimization of thorium-based fuel configurations f or minimizing slightly used nuclear fuel and radiotoxicity In small modular reactors

Thorium fuel Performance: A comparative study on thorium's efficiency in PWR reactors