Abstract:Titanium and its alloys (especially Ti6Al4V) are widely employed in aerospace and biomedical industry. Wire electric discharge machining is common in practice to machine this difficult-to-cut material. But owing to the thermo-electric nature of the process, it is challenging to have adequate level of surface integrity. This primary concern needs to be addressed as it mainly influences the surface mechanical characteristics. Therefore, the present research aims to address the aforesaid issues using well-known multipass strategy. Understanding the multipass process dynamics and requirements, the potentiality of brass wire diameters was comprehensively examined and explored during WEDM of Ti6Al4V. Considering higher cost, unavailability, environmental hazards, and straightness issues of novel zinc-coated wire electrodes, readily available brass wires provide a cheaper and widely acceptable solution to enhance surface integrity of machined parts if equivalent results can be somehow made possible. For that sake, three different brass wire diameters; 0.15 mm, 0.2 mm, and 0.25 mm have been considered to evaluate their impact on surface roughness, recast layer thickness, overcut, machined surface microhardness, and cutting speed using multipass cutting technique. Experimental results revealed that 0.15 mm uncoated brass wire can produce white layer result equivalent to Topas Plus X wire (Cu core-double Zn-rich layer coating) which outperformed among all zinc-coated wires used in previously published research. Moreover, among different diameter brass wires, surface roughness is improved by 25% using multipass cutting with 0.15 mm diameter in comparison to its counterparts. Scanning electron microscope (SEM) analysis depicts that the said combination reduces recast layer thickness from 39.04 μm to 14.6 μm (~ 1.5 times lesser value). In addition to that, smaller diameter (0.15 mm) provides the maximum cutting rate in rough cuts (which consume maximum machining time) and dimensional accuracy.

Effect of Wire Electric Discharge Machining Parameters on Material Removal Rate in Machining of Titanium Grade 7 Alloy

Curved Profiles Machining of Ti6Al4V Alloy Through WEDM: Investigations on Geometrical Errors

Investigation on Surface Roughness and MRR in WEDM of Titanium Grade 7 (Ti-0.15Pd) Alloy using Statistical Techniques

Experimental Study on Parametric Effect of Wire Electric Discharge Machining of Titanium Grade 2 Alloy Using Cryogenic Treated Wire

Evaluating Optimal Parameters for Machining Selective Laser Melting Titanium Alloy Using Wire Cut Electrical Discharge Machining

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

Machinability of titanium alloy through electric discharge machining

Machining efficiency and geometrical accuracy on micro-EDM drilling of titanium alloy

A study on Electrical Discharge Machining of Titanium Grade2 with experimental and theoretical analysis

Multi-Response Optimization and Surface Integrity Characteristics of Wire Electric Discharge Machining α-Phase Ti-6242 Alloy

Experiments of Ti6Al4V manufactured by low-speed wire cut electrical discharge machining and electrical parameters optimization

Performance analysis in WEDM of titanium grade 6 through process capability index

Modeling and analysis of titanium alloy in wire-cut EDM using Grey relation coupled with principle component analysis

Experimental study on high-efficiency DC short electric arc milling of titanium alloy Ti6Al4V

Recast Layer Formation during Wire Electrical Discharge Machining of Titanium (Ti-Al6-V4) Alloy

Electric Discharge Machining of Ti6Al4V ELI in Biomedical Industry: Parametric Analysis of Surface Functionalization and Tribological Characterization

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

Electric Discharge Machining of Titanium Alloy under Cu Mixed Dielectric Medium

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses

Influence of Different Dielectrics and Machining Parameters for Electrical Discharge-Assisted Milling of Titanium Alloy

Effect of Electrode Materials on Different EDM Aspects of Titanium Alloy