Abstract:Application of ultra-high-performance concrete (UHPC) in joints can improve the impact resistance, crack resistance, and durability of structures. In this paper, the direct shear performance of ultra-high-performance concrete (UHPC) adhesive joints was experimentally studied. Twenty-four direct shear loading tests of UHPC adhesive joints were carried out considering different interface types and constraint states. The failure modes and load-slip curves of different interfaces were studied. Results indicated that passive confinement could enhance the strength and ductility of the interface; the average ultimate bearing capacity of the smooth, rough, grooved, and keyway specimens with passive restraint were, respectively, increased by 11.92%, 8.91%, 11.93%, and 17.766% compared with the unrestrained ones. The passive constraint force changes with the loading and finally tends to be stable. The epoxy adhesive has high reliability as a coating for the UHPC interface. The adhesive layer is not cracked before the failure of the specimen, which is also different from the common failure mode of adhesive joints. Failure of all specimens occurred in the UHPC layer, and the convex part of the groove interface shows the UHPC matrix peeling failure; the keyway interface is the shear damage of the key-tooth root, and the rest of the keyway showed UHPC surface peeling failure. According to the failure mode, the shear capacity of UHPC keyway adhesive joints under passive restraint is mainly provided by the shear resistance of key teeth, the friction force of the joint surface, and the bonding force of the UHPC surface. The friction coefficient was determined based on the test results, and the high-precision fitting formula between the shear strength of the UHPC surface and the passive constraint force was established. According to the Mohr stress circle theory, the proposed formula for direct shear strength of UHPC bonded joints under passive constraint was established. The average ratio of the proposed UHPC adhesive joint calculation formula to the test results was 0.99, and the standard deviation was 0.027.

Study on interfacial performance of ordinary concrete composite structure strengthened by ultra-high performance concrete —A review

A Review of Self-Sensing Ultra-High Performance Concrete: Towards Next-Generation Smart Structural Materials

Interface Shear Failure Behavior Between Normal Concrete (NC) and Ultra-High Performance Concrete (UHPC)

Mechanical behavior of natural bonding interface in hollow steel-UHPC composite bridge deck

Monolithic and non-monolithic interface shear performance of ultra-high performance concrete

Analysis of Structural Parameters of Steel–NC–UHPC Composite Beams

Experimental and Numerical Study on the Microstructure and Chloride Ion Transport Behavior of Concrete-to-concrete Interface

Development on Ultra-high Performance Concrete in Building Structures

EXPERIMENTAL RESEARCH ON TENSILE AND SHEAR BEHAVIOUR OF THE INTERFACE BETWEEN NON-STEAM-CURED UHPC AND STEEL PLATE STRUCTURE

Study on the Flexural Performance of Ultrahigh-Performance Concrete-Normal Concrete Composite Slabs

Mechanical properties, durability and application of ultra-high-performance concrete containing coarse aggregate (UHPC-CA): A review

Experimental Investigation on Interface Performance of UHPC-Strengthened NC Structure through Push-Out Tests

Interfacial bonding between graphene oxide and calcium silicate hydrate gel of ultra-high performance concrete

Interfacial Shear Performance of Epoxy Adhesive Joints of Prefabricated Elements Made of Ultra-High-Performance Concrete

Ultra-high performance concrete: Mix design, raw materials and curing regimes-A review

Quantifying Bonding Characteristics between UHPC and Normal-Strength Concrete for Bridge Deck Application

Shear Fracture Performance of the Interface Between Ultra-High Toughness Cementitious Composites and Reactive Powder Concrete

Enhancing Interface Shear Performance and Bending Resistance of UHPC Permanent Formwork for Composite Short Beams by Different Interface Treatment

Mechanical Behavior and Design Properties of Ultra-High-Performance Concrete

Mesoscopic shear behavior and strength characteristic of UHPC-NC interface considering the combined effect of mechanical interlocking and dowel action

Experimental and Numerical Investigation of the Interfacial Properties of Non-Steam-cured UHPC-steel Composite Beams