Abstract:Introduction. Modern conditions of iron and steel making industry require production of high-quality competitive metal products. Thus, the removal of sulfur at the lowest cost has been becoming increasingly important.Problem Statement. The major amount of sulfur in iron and steel making comes with charge materials in sintering blast furnace production. When using out-of-furnace processing of hot metal in hot metal desulfurizationand slag removal facilities, the degree of hot metal desulfurization can be 75—99%. This ensures the production of hot metal with a sulfur content in the range of 0.002—0.015%.Purpose. The analysis of changes in the sulfur content of hot metal and in the slag composition in the processchain of steel production, followed by the development of technical solutions and process methods to eliminate theresulfurization of hot metal.Materials and Methods. Our calculations, based on the actual data of Ukrainian and Chinese iron and steelmaking facilities. The selected samples of slag and hot metal have been analyzed with the use of raster spectralmicroscopy methods. In the studies of sulfur content at various stages of smelting, the method of material balancecalculation has been employed.Results. In the slag phase, along with systems of CaO ∙ SiO2 ∙ Al2O3 type with diff erent ratios of componentscontaining 0.2—3.5% sulfur, CaxSiyAlz type systems containing up to 1% sulfur have been detected. In the beads, the sulfur content varies within 0.1—0.85%. Sulfur is present in the form of sulfi des of (Fe, Mn)S type, mainlyMnS, while in non-metallic inclusions of the beads, the sulfur content ranges within 15—30%. The residing ladleslag after desulfurization should not exceed 0.5—0.7 kg/t of hot metal.Conclusions. To prevent the resulfurization of hot metal during its discharge from a blast furnace, it is advisable to rationalize ladle slag modes, by adjusting ladle slag composition, increasing the degree of ladle cleaning from the slag residing from previous loads and inducing a slag cover in the absence of ladle slag. The conducted studies have shown that sulfur from the slag does not return to the hot metal and resulfurization does not occur, which is explained by the protective eff ect of residual magnesium.

Behavior of Copper and Sulfur During High-Temperature Sulfurization Of Copper-Smelting Slags with Elemental Sulfur

Kinetics of copper leaching from direct-to-blister copper flash smelting slag by sulfuric acid

Recovery of high-grade copper matte by selective sulfurization of CuO–Fe2O3–SiO2–CaO system

The Phase Transition and Element Distribution of Copper Smelting Slag in the Cooling—Sulfidation Process

Change in Slag Composition and Sulfur Content of Hot Metal in the Process Chain of Blast Furnace — Hot Metal Desul furization Complex — Converter (BOF)

Thermodynamics Evaluation and Verification of High-Sulfur Copper Slag Composite Agglomerate in Oxidation-Roasting-Separation-Leaching Process

A green method to clean copper slag and rapidly recover copper resources via reduction-sulfurizing smelting and super-gravity separation at low temperature

Thermodynamic Phase Conversion Mechanism on Copper–Cobalt Slag Cleaning Process Using Gypsum Wastes as Sulfurizing Agent

Thermochemical Properties of Copper-Iron-Sulfur Alloy as Reference Metallic Phase for Analyzing Resulfurization

Control of Copper Content in Flash Smelting Slag and the Recovery of Valuable Metals from Slag—A Thermodynamic Consideration

Reduction of Copper Smelting Slag by Carbon for Smelting Cu-Fe Alloy

Ammoniacal System Mechanisms for Leaching Copper from Converter Slag

Characterization, Concentration, and Speciation of Metal Elements in Copper Slag: Implications for Secondary Metal Recovery

Experimental Study on the Phase Equilibrium of Copper Matte and Silica-Saturated FeO X -Sio 2 -Based Slags in Pyrometallurgical WEEE Processing

Breaking the Fe3O4-wrapped copper microstructure to enhance copper–slag separation

An efficient approach to utilize copper smelting slag: Separating nonferrous metals and reducing iron oxide at high temperature

Density Tuning in Conjunction with Pelletizing of Reductants for Enhanced Recovery from Copper Smelting Slag

Recovery of Copper, Lead and Zinc from Copper Flash Converting Slag by the Sulfurization-Reduction Process

Pyrometallurgical Reduction of Copper Slag with Biochar for Metal Recovery

Improved Settling Mechanisms of an Industrial Copper Smelting Slag by CaO Modification

Reduction Kinetics of Copper Slag by H2