Abstract:The industrial torch system is used to handle large amounts of flammable, toxic, and corrosive gases emitted during accidents or normal production processes. It utilizes open flames to burn off the gas pollutants. This study employs computational fluid dynamics (CFD) to investigate the combustion characteristics and efficiency of flames under high-velocity jet, aiming to address the issue of low combustion efficiency under high-velocity jet conditions. A three-dimensional flame model was established using methane and air as fuel, in order to investigate the variations and impact mechanisms of the combustion flame temperature field and carbon dioxide mass fraction distribution under different jet velocities, pilot component temperatures, and equivalence ratios. The reasons for low combustion efficiency under high-velocity jet conditions were analyzed. It was proposed to increase the combustion efficiency of the flame by raising the temperature of the pilot component, which differs from the traditional method of adding combustion-assisting gases. The combustion efficiency of flames under various operating conditions was evaluated. The results showed that as the jet velocity ( v ) increased from 49.6 m/s to 65 m/s, the height of the combustion flame in the vertical direction decreased continuously. Additionally, the high-temperature region at the center of the flame gradually decreased, leading to a 5.26% decrease in the highest flame temperature and a 3% decrease in combustion efficiency. When v = 70 m/s, the high-velocity fuel flow penetrated the ignition source, causing a large amount of methane to escape into the atmosphere without combustion, resulting in flame extinction. Elevating the temperature ( T ) of the pilot component can reduce the impact of high-velocity jet on combustion efficiency. When T = 2000 K, the flame reignites with a combustion efficiency of 94.1%. As the mass flow rate of the fuel composition inlet is reduced from 33.45 × 10 −5 kg/s to 12.74 × 10 −5 kg/s, the highest temperature of the combustion flame drops from 2072 K to 1451 K. As the equivalence ratio ( φ ) increases from 1.05 to 1.2, the height of the combustion flame in the vertical direction decreases continuously, resulting in a 0.7% decrease in the highest flame temperature and a 10.5% decrease in combustion efficiency.

Study on the effect of combustion efficiency of variable thrust rocket engines

Effect of dielectric barrier discharge methane reforming products on the combustion performance of rocket engine

Combustion performance of an evaporative flameholder under subsonic-supersonic mixing inflow

A numerical study of counterflow diffusion flames of methane/air at various pressures

Modeling of Supercritical-Pressure Turbulent Combustion of Hydrocarbon Fuels Using A Modified Flamelet-Progress-Variable Approach

Numerical Investigation of Work Cycle Characteristics in the Combustion Chamber of a Lox/Methane Liquid-Propellant Rocket Engine Featuring Reductant Power Gas Combustion

Effects of Near Wall Flow and Non-equilibrium Reaction Coupling on Heat Flux Prediction Inside a 7-Elements GOX/GCH4 Combustion Chamber

Numerical simulation of combustion in the chamberof a model low-thrust rocket engine operating on the gaseous oxygen–methane components

Numerical Analysis of Combustion and Film Cooling in LOx-Methane Rocket Engine

Throttling simulation and control of liquid oxygen/liquid methane rocket engine pressurized by the electric pump

Efficiency study of low calorific value high momentum turbulent jet combustion flame

Numerical Investigation on the Effect of Fuel-Rich Degree in the RBCC Engine under the Ejector Mode

Study on the effect of high-pressure methane jet on lean burn laminar flame

Experimental study on the combustion and pressure drop characteristics of a pintle injector for LOX/kerosene rocket engine

Investigation on Burning Behaviors of Aluminum Agglomerates in Solid Rocket Motor with Detailed Combustion Model

Effect of inhomogeneous methane-air mixtures on combustion characteristics in a constant volume combustion chamber

Effect of synergistic impact gas injection device on secondary combustion in boron-based ducted rockets

Numerical Study of Combustion and Cooling Performance of a Gaseous Oxygen and Gaseous Methane Rocket Combustor with the Needle-Bolt Injector

Modeling of Spray Combustion and Heat Transfer of MMH/N2O4 in a Small Rocket Engine Using Different Mechanisms

Numerical simulation of the effect of multiple factors on the ignition process of a solid rocket motor

Effects of Injection Schemes on the Performance of Powdered Magnesium-Liquid CO 2 Rocket Engine