Abstract:In this work, high oleic soybean oil was used to synthesize an acrylic monomer (HOSBM), which was copolymerized with myrcene and styrene at a 90:10 wt/wt feed ratio to obtain copolymers containing myrcene (HOSBM-M) and styrene (HOSBM-S). These copolymers were employed here as macromolecular plasticizers to modify the brittle nature of polystyrene (PS). Specifically, the soy-based copolymers were added to commodity polystyrene at 5–20 wt %, and the copolymer effect on the polymer blends’ structure and behavior was studied. We report on the blends’ morphology and thermal/mechanical properties and employ thermodynamic and mechanical models to understand the interactions between the PS matrix and the HOSBM copolymer dispersed phase. Microscopy indicated that the mixed materials have a phase-separated structure composed of the PS-based matrix and the copolymer-based dispersed phase. Our thermodynamic estimations and measurement of the thermal transitions showed that the blends are partially miscible, where a fraction of PS chains migrated into the dispersed phase and the copolymer was partially situated in the PS matrix. Therefore, HOSBM-M and HOSBM-S plasticize the PS matrix, decreasing the glass transition temperature and moduli. The mechanical properties of the blends depicted a trade-off between the flexural modulus, strength, and toughness. Although the PS/HOSBM-S blends showed decreased storage/flexural moduli and strength compared to neat PS, the decline was significantly lower than that demonstrated by the HOSBM-M blends. Moreover, adding the HOSBM-S copolymer to PS at 10–15 wt % loading enhances the material’s extensibility compared to pure PS. The trend in the toughness values shows that the optimal HOSBM-S loading is 10 wt % to obtain materials with the best middle ground between flexural modulus, strength, extensibility, and toughness.

Combining ternary phase diagrams and multiphase coupled matrix-based Monte Carlo to model phase dependent compositional and molar mass variations in high impact polystyrene synthesis

Effect of stirring speed and its change time on phase inversion of high impact polystyrene

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Phase inversion during bulk copolymerization of N-phenylmaleimide/styrene in presence of polybutadiene (II): Effects of operation conditions and recipes on occurrence of phase inversion and structure of rubber phase

Full‐range Kinetic Study on Bulk Syndiotactic Polymerization of Styrene with Homogeneous Metallocene Catalysis

A Two‐phase Method of Moments Model for High‐impact Polystyrene Phase Inversion Conversion and Molecular Properties

Influence of styrene-b-butadiene copolymer types on phase morphology and polymer partitioning between demixed-macrophases from HIPS-mimicking unstable blends

Co-Continuous Polymeric Nanostructures Via Simple Melt Mixing of Ps/Pmma

Blending Properties of Polyethylene Blends Obtained by Hybrid Catalyst on Composite Support

Molecular Simulation of the Effect of Graft Structure on the Miscibility of High‐impact Polystyrene Blends

Modelling the morphology evolution of polymer materials undergoing phase separation

Phase equilibrium and mixing thermodynamics of polystyrene with copolymers of styrene and methyl methacrylate

Phase Separation in Blends of Homopolymer and Graft Copolymer Based on Styrene and Butadiene

Monte Carlo simulations of a coarse grained model for an athermal all-polystyrene nanocomposite system

Double reaction-induced microphase separation in epoxy resin containing polystyrene-block-poly(ε-caprolactone)-block-poly(n-butyl acrylate) ABC triblock copolymer

Hierarchical modelling of polystyrene melts: from soft blobs to atomistic resolution.

Synthesis and Microphase Separation Behavior of Random, Mixed Cylindrical Brush Copolymers Bearing Polystyrene and Poly(ε-caprolactone) Side Chains

Cost‐efficient modeling of distributed molar mass and topological variations in graft copolymer synthesis by upgrading the method of moments

Reaction-Induced Microphase Separation In Epoxy Thermosets Containing Block Copolymers Composed Of Polystyrene And Poly(Epsilon-Caprolactone): Influence Of Copolymer Architectures On Formation Of Nanophases

Plasticization of Polystyrene with Copolymers Based on High Oleic Soybean Acrylic Monomer

Reaction-induced Microphase Separation in Thermosetting Blends of Epoxy Resin with Poly(methyl Methacrylate)-Block-polystyrene Block Copolymers: Effect of Topologies of Block Copolymers on Morphological Structures