Abstract:Cold Spray is a solid deposition process that can expand the field of application of polymeric materials thanks to the build-up of a metallic coating that improves their electrical properties and the wear resistance, among others. The novelty of the Cold Spray deposition on polymers has as drawback the lack of processing models that allow to choose the manufacturing parameters and forecast the coatings and substrates properties. In this work, the influence of the processing parameters for Aluminium-Zinc coating build-up via Low Pressure Cold Spray on polyamide 12 additively manufactured via Fused Filament Fabrication was investigated. Several sets of processing parameters combinations were systematically modified to establish the deposition window, leading to a final set that allowed to determine the physical, microstructural, and mechanical properties of the coatings, and the physical and thermal properties of the polymeric substrate. For the fixed gas pressure of 0.45 MPa and gas temperature of 500 °C, the scanning speed and the powder mass flow rate had a strong influence. Thick coatings (around 850 μm in size) were achieved at high powder mass flow rate (26 g/min) at the expense of low bond strength (between 1 and 3 MPa). The surface roughness acquired the highest values in those samples where erosion took place, occurring this phenomenon at small standoff distances and low powder mass flow rate, and no finding any relationship with the transverse gun speed. The generation of an interface layer of mixed metallic particles polymeric substrate plays a key role in the subsequent metallic coating growth, with thicknesses that ranged from 30 μm to 200 μm. In the substrate, the crystallinity degree of the polyamide underneath the coating increased, evidence of a heat affected zone where temperatures around the crystallisation temperature were reached, that also promoted stretching of the polymeric substrate due to dilatational phenomena. All this accompanied of an overall decrease in the thickness of the PA12 coupon after coating build up deposition with the high powder mass flow rate. This evidence indicates that a large plastic deformation of the polymeric substrate at the most energetic combination of processing parameters took place.

A comparative study of the fluidized-bed coating of cylindrical metal surfaces with various thermoplastic polymer powders

Curing Behavior of Powder Coating of Polyester Resin

Surface Metallization and Ceramic Deposition on Thermoplastic-Polymer and Thermosetting-Polymer Composite Via Atmospheric Plasma Spraying

One-step fabrication of thermal sprayed polymer coating on metals

Manufacturing of Corrosion-Resistant Surface Layers by Coating Non-Alloy Steels with a Polymer-Powder Slurry and Sintering

Polymer Coating On The Surface Of Zirconia Nanoparticles By Inductively Coupled Plasma Polymerization

Pull-off Testing and Electrical Conductivity of Sn-Based Metal Powder Mixtures Cold Sprayed on Carbon Fiber-Reinforced Polymers

Experimental Study on Film Thickness and the Problem of Free Surface Film Flow in Dip Coating

Effect of Phenolic Resin Coating Thickness on Mechanical Properties and Corrosion Resistance of Metal Materials

Influence of sub-monolayer quantities of carbon nanoparticles on the melting and crystallization behavior of polyamide 12 powders for additive manufacturing

Effect and performance analysis of different surface treatments on polymer-metal friction pairs

Metallisation of additive manufactured polyamide 12 by low pressure cold spray

Decorative Chromium Coatings on Polycarbonate Substrate for the Automotive Industry

Improvement of the deposition efficiency and adhesion strength of cold sprayed fluoropolymer coating by laser surface texturing of the substrate

Utilizing response surface methodology for the microstructural examination of CeO2/GNP composite coating applied via air plasma spraying and post-treated with spark plasma sintering

Quality over Quantity: How Different Dispersion Qualities of Minute Amounts of Nano-Additives Affect Material Properties in Powder Bed Fusion of Polyamide 12

The Review of Powder Coatings

Computational Analysis of Cold Spraying Polymer-Coated Metallic Particles on Fiber-Reinforced Polymer Substrates

Effect of Feedstock Powder Intrinsic Characteristics on the Tribological Behavior of Inductively Remelted NiCrBSi Flame-Sprayed Coatings

Electron-Beam and Plasma Oxidation-Resistant and Thermal-Barrier Coatings Deposited on Turbine Blades Using Cast and Powder Ni(Co)CrAlY(Si) Alloys Produced by Electron Beam Melting IV. Chemical and Phase Composition and Structure of Cocralysi Powder Alloys and Their Use

Enhancing colloid stability of polymer microspheres in water through SiO2 coating: Effects of coating cycles and surface coverage