Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

Developing mortar using limestone flash-calcined dredged sediment/millstone-clay cement binder (LFC)

The Effect of μ-Limestone Additions on the Mechano-Chemical and Microstructural Properties of Slag and Binary Slag/Ground Fly Ash Alkaline-Activated Binders

Microstructural investigation and performance of LC3 cementitious materials

Development of eco-friendly binder using metakaolin-fly ash–lime-anhydrous gypsum

Use of spent fluid catalytic cracking catalyst (FCC) in Limestone Calcined Clay Cement (LC3) systems: Studies in pastes and mortars

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Influence of calcined sediment inputs on the mechanical behavior of fiber-reinforced concrete in an aggressive environment

A Fresh View on Limestone Calcined Clay Cement (LC3) Pastes

Mechanical Properties and Microstructure of Low Carbon Binders Manufactured from Calcined Canal Sediments and Ground Granulated Blast Furnace Slag (GGBS)

Properties of Mortars Formulated from Self-Compacting High-Performance Concrete Containing Various Mineral Additions

The Synergistic Effect of Calcained Coal-Series Kaolinite and Limestone on the Hydration of Portland Cement

Mechanical Performance of Portland Cement, Coarse Silica Fume, and Limestone (PC-SF-LS) Ternary Portland Cements

Design and characterization of iron–calcium–aluminium–silicate–hydrate as low-temperature binder

Developing Low Cost Eco-friendly Restoration Mortars for Historic Lime-based Stucco and Building Materials

The Influence of External Sulfate Attack on the Durability of Reinforced Mortars in the Presence of Calcined River Sediments

Microstructural and Compressive Strength Analysis for Cement Mortar with Industrial Waste Materials

Compressive Strength and Microstructural Development of Cementitious Mixtures Incorporating Ultrafine Granulated Blast Furnace Slag

Alkali-Activated Binders as Sustainable Alternatives to Portland Cement and Their Resistance to Saline Water

Effects of key factors on the compressive strength of metakaolin and limestone powder-based alkali-activated concrete mixtures: An experimental and statistical study

Investigation of Low-Calcium Circulating Fluidized Bed Fly Ash on the Mechanical Strength and Microstructure of Cement-Based Material