Abstract:Solid oxide fuel cell (SOFC) is an energy conversion device that converts chemical energy in fuels into electric energy directly with the advantages of high efficient, clean, and wide fuel adaptability. Most hydrocarbons such as natural gas, ethane and bio-oil can be used as fuels in SOFC. When a hydrocarbon fuel, such as methane (CH4), is directly used for IT-SOFCs without prereforming by adding oxygen, steam or carbon dioxide, it is electrochemically oxidized on the triple-phase boundaries (TPB) with a strong tendency of carbon deposition in the traditional Ni-based anode. In this paper, we introduce an extra internal reforming layer on the surface of anode-support. The layer of a LaCrO3 based perovskite with exsolved Ni nanoparticles catalyst (La0.6Sr0.2Cr0.85Ni0.15O3 showed high stability in reducing atmosphere and excellent catalytic performance. Based on this, two types of anode-supported cell are fabricated by tape casting, screen printing and sintering processes. The first one is a conventional anode supported cell with a configuration of Ni-GDC/GDC/GDC-LSCF (cell 1); and the other contains a reforming layer mixed with La0.6Sr0.2Cr0.85Ni0.15O3 and SDC which was a well coking resistant promoters (cell 2). When CH4–CO2 was used as the fuel, which was supposed to yield syngas with the H2–CO ratio close to unity, the polarization resistance of the cell 1 reach at 0.247 Ω cm2 whereas the value of cell 2 is 0.082Ω cm2 at 750 °C. These results implied that both the physical and the chemical properties of the TPB have been altered drastically during internal dry reforming since that Ni-based anode show poor catalytic performance in reforming and are prone to coking. Consequently, the maximum power density for cell 1 was 470 mW cm-2 and the cell suffered from degradations during a 1 h galvanostatic operation at 1 A cm-2. The performances of the cell 2 are significantly increased above the level of the cell 1, demonstrating a peak power density at 929 mW cm-2 at 750 °C and a stable cell voltage at 1 A cm-2 and 750 °C for 48 h. Carbon deposition in the anode region of the tested cell 2 is not detected, as the La0.6Sr0.2Cr0.85Ni0.15O3 is a more active and stable catalyst than the Ni-based anode-support for dry reforming. Finally we demonstrated the strong interaction between the exsolved nanoparticles and the substrate could prevent coking deposition and proposed a promising configuration of double-layer anode for solid oxide fuel cells with on-cell reforming. Figure 1

Structured Catalyst for Indirect Internal Reforming (IIR) of Biogas in Solid Oxide Fuel Cell (SOFC)

Co-Generation of Electricity and Syngas on Proton-Conducting Solid Oxide Fuel Cell with A Perovskite Layer As A Precursor of A Highly Efficient Reforming Catalyst

Direct carbon dioxide-methane solid oxide fuel cells integrated for high-efficiency power generation with La0.75Sr0.25Cr0.5Fe0.4Ni0.1O3–δ-based dry reforming catalyst

Self-Confinement Created for a Uniform Ir–Ni/SiO2 Catalyst with Enhanced Performances on CO2 Reforming of Methane

Paper‐structured catalyst with a dispersion of ceria‐based oxide support for improving the performance of an SOFC fed with simulated biogas

Solid Oxide Fuel Cells Fueled by Simulated Biogas: Comparison of Anode Modification by Infiltration and Reforming Catalytic Layer

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

Proton-Conducting La-Doped Ceria-Based Internal Reforming Layer for Direct Methane Solid Oxide Fuel Cells

Ni and Ru bimetal nanoparticles-anchored porous Mo 2 C nanorods used as an internal reforming catalyst layer for hydrocarbon-fueled solid oxide fuel cells

Ru-Ce0.7Zr0.3O2−δ as an Anode Catalyst for the Internal Reforming of Dimethyl Ether in Solid Oxide Fuel Cells

Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

Direct carbon dioxide-methane solid oxide fuel cells combined with in-situ exsolution perovskite La0.75Sr0.25Cr0.5Fe0.4Cu0.1O3-δ-based dry reforming catalysts

Co‐Generation of Electricity and Chemicals From Methane Using Direct Internal Reforming Solid Oxide Fuel Cells

Numerical Analysis of the Internal Fuel Processing in Solid Oxide Fuel Cells

Single-chamber solid oxide fuel cells with nanocatalyst-modified anodes capable of in situ activation

Use of A Catalyst Layer for Propane Partial Oxidation in Solid Oxide Fuel Cells

A review on anode on-cell catalyst reforming layer for direct methane solid oxide fuel cells

Catalyst with CeO 2 and Ni Nanoparticles on a LaCrO 3 -Based Perovskite Substrate for Bio-Alcohol Steam Reforming and SOFC Power Generation

Anode Catalyst Layers for Direct Hydrocarbon and Internal Reforming SOFCs

Partial oxidation of methane in a Zr 0.84Y 0.16O 1.92-La 0.8Sr 0.2Cr 0.5Fe 0.5O 3-δ hollow fiber membrane reactor targeting solid oxide fuel cell applications

Synthesis Gas Production with NiO−MgO/γ-Al2O3/Cordierite Monolithic Catalysts in a Pilot-Scale Biomass-Gasification-Reforming System