Abstract:The aim of the study was to compare the properties of inulin hydrogels obtained with different methods, e.g., the traditional-thermal method and new, non-thermal methods, used in food production, like ultrasonic, high-pressure homogenization (HPH), and high hydrostatic pressures (HHPs). It was found that each of the compared induction methods allowed for obtaining inulin hydrogels. However, the use of non-thermal induction methods allows for obtaining a gel structure faster than in the case of thermal induction. In addition, hydrogels obtained with new, non-thermal methods differ from gels obtained with thermal treatment. They were characterized by higher stability (from 1.7 percent point-of-stability parameters for HHP 150 MPa to 18.8 for HPH II cycles) and in most cases, by improved microrheological properties-lower solid-liquid balance toward the solid phase, increased elasticity and viscosity indexes, and lowering the flow index. The gels obtained with the new, non-thermal method were also characterized by a more delicate structure, including lower firmness (the differences between thermal and non-thermal inductions were from 0.73 N for HHP at 500 MPa to 2.39 N for HHP at 150 MPa) and spreadability (the differences between thermal and non-thermal inductions were from 7.60 Ns for HHP at 500 MPa to 15.08 Ns for HHP at 150 MPa). The color of ultrasound-induced inulin gels, regarding the HPH and HHP technique, was darker (the differences in the L* parameter between thermal and non-thermal inductions were from 1.92 for HHP at 500 MPa to 4.37 for 10 min ultrasounds) and with a lower a* color parameter (the differences in the a* parameter between thermal and non-thermal inductions were from 0.16 for HHP at 500 MPa to 0.39 for HPH II cycles) and b* color parameter (the differences in the b* parameter between thermal and non-thermal inductions were from 1.69 for 5 min ultrasounds to 2.68 for HPH II cycles). It was also found that among the compared induction methods, the high-pressure technique has the greatest potential for modifying the properties of the created inulin hydrogels. Thanks to its application, depending on the amount of applied pressure, it was possible to obtain gels with very different characteristics, both delicate (i.e., soft and spreadable), using HHP at 150 MPa, and hard, using HHP at 500 MPa, the closest in characteristics to gels induced with the thermal method. This may allow the properties of hydrogels to be matched to the characteristics of the food matrix being created.

Factors affecting gel formation of inulin

Kinetic Study of Thermally Induced Inulin Gel

Alteration of the structural properties of inulin gels

Amorphous and crystal inulin behavior in a water environment

Effect of inulin on texture and clarity of gellan gels

Heat-induced inulin-gluten gel: Insights into the influences of inulin molecular weight on the rheological and structural properties of gluten gel to molecular and physicochemical characteristics

Mechanisms of inulin addition affecting the properties of chicken myofibrillar protein gel

Studies on the Inulinase Protective Agent of the {\sl Aspergillus Niger} U#gamma#--2

Rheological and Micro-Rheological Properties of Chicory Inulin Gels

Characterizing High Pressure Phase Transitions of Gelatin Gel and Assessing Microstructural, Gel Properties, and Texture Changes Following Pressure Shift Freezing and Ice I to Ice III Phase Transition

Effect of thermal and mechanical factors on rheological properties of high performance inulin gels and spreads

Ice-crystal Formation in Gelatin Gel During Pressure Shift Versus Conventional Freezing

Effects of inulin with different polymerization degrees on the structural and gelation properties of potato protein

Thermal and Modern, Non-Thermal Method Induction as a Factor of Modification of Inulin Hydrogel Properties

Inulin for Surimi Gel Fortification: Performance and Molecular Weight-Dependent Effects.

Effect of inulin with different degree of polymerisation on textural and rheological properties of wheat starch - Effect of inulin on gel properties of starch

Physicochemical characterization and stability of inulin gels

Study on the gel properties, interactions, and pH stability of pea protein isolate emulsion gels as influenced by inulin

Effects of inulin on the gel properties and molecular structure of porcine myosin: A underlying mechanisms study

Effects of gellan gum and inulin on mixed‐gel properties and molecular structure of gelatin

Effect of high hydrostatic pressure on formation and rheological properties of inulin gels