Abstract:The objective of the LuFo VI-1 project CATeW (Coupled Aerodynamic Technologies for Aircraft Wings) consists in multifidelity analyses to assess the potential for aerodynamic efficiency increase by combined application of hybrid laminar flow control and variable camber technologies to the wing of a transonic transport aircraft. Individually, both technologies have proven to lead to major aerodynamic drag reductions. An evaluation of the coupled technologies is, therefore, expected to show an even higher potential due to synergy effects. To derive conclusions on system level, low-fidelity (LowFi) overall aircraft design methodologies will be applied for the analysis of a medium haul reference aircraft in the course of the project, while complex aerodynamic phenomena are modelled with high-fidelity (HiFi) computational fluid dynamics methods. The paper at hand presents results of aerodynamic analyses on both fidelity levels for the wing of the turbulent reference configuration CATeW-01, featuring the technology combination as a retrofit. Furthermore, this work encompasses adaptations and implementations performed within both the LowFi and HiFi toolchains. The LowFi toolchain already incorporates several modules for the proposed technology combination. A short presentation of the LowFi-toolchain is given, along with the modeling approach in the HiFi framework using mesh deformations and a mass flux boundary condition. Comparative studies of the turbulent flow field around the wing show good agreement of predicted load distributions in both numerical frameworks, studies based upon the HiFi approach attest the potential for efficiency increase due to the variable camber technology, incorporated by means of Adaptive Dropped Hinge Flap (ADHF) deflections. Considering the coupled application, four different constant suction mass flow rates are examined, where the maximum mass flow causes laminar flow extending over the entire suction panel, thus moving the transition location from the wing's leading edge to the end of the suction panel. When being coupled with ADHF deflections, again the variable camber technology leads to a reduction of the wing's pressure drag component with the simultaneous application of boundary layer suction further promoting drag reduction with increasing suction rate. While the combined application shows no mutual inhibition, major reciprocal effects are not directly observable when applying the combination as a retrofit to the reference configuration CATeW-01. This is mainly attributed to the limited extend of laminar flow, thus indicating the necessity for optimization in wing geometry and operating parameters, to achieve extensive areas of laminar flow and to promote the aspired synergy effects.

CFD ANALYSIS OF A BLENDED BODY AIRCRAFT

Unsteady Flow Simulation of a Variable-Sweep Morphing Aircraft Coupled with Flight Control System

Constrained Large-Eddy Simulation and Detached Eddy Simulation of Flow Past a Commercial Aircraft at 14 Degrees Angle of Attack

Multiobjective Shape Optimization of A Hypersonic Lifting Body Using A Correlation-Based Transition Model

Multi-Fidelity Design Optimization of a Long-Range Blended Wing Body Aircraft with New Airframe Technologies

A CFD Analysis of Wingtip Devices to Improve Lift and Drag Characteristics of Aircraft Wing

Numerical two-dimensional optimization of a cylindrical fuselage for bioinspired unmanned aerial vehicle based on non-dominated sorting genetic algorithm-II

Design and Analysis of Flexible Wing

Reliable method of aerodynamic analysis using computational fluid dynamics and scaled models in the development process of a Very Light Airplane

Design of a Novel Aerofoil of a Light Aircraft for Robust Aerodynamic Performance at High Reynolds Number Regime Using XFLR5

Optimization of positional parameters of close-formation flight for blended-wing-body configuration

A CFD-Based Collaborative Approach for Box-Wing Aircraft Aerodynamic Assessment: The PARSIFAL Study Case

Comparative Analysis of Improved Aerodynamic Performance: Computational Fluid Dynamics Study of the Trailing Edge Morphing Concept Parameters

Performance analysis of composite laminates wing skin with the aid of fluid structure interaction of aerodynamic loading-structural analysis

Numerical analyses of a reference wing for combination of hybrid laminar flow control and variable camber

Design Optimization of Cessna 172 Wing With Biomimetic Design Approach

An Automated and Efficient Aerodynamic Design and Analysis Framework Integrated to PANAIR

Experimental Study on the Effect of Boundary Layer Control on the Aerodynamics Characteristics of NACA 0021 Aerofoil

Optimizing Obscurity: Advancing Stealth Capabilities and Performance of BWB Fighter with Symmetric Supercritical Airfoils

Optimization and Analysis of a Blown Flap Based on a Multielement Airfoil

Design and Analysis of A Two-stage Bionic Flapping Wing Aircraft