Abstract:One of the developing areas of tribotechnical materials science is the development and study of nanocomposite materials for movable joints operating under extreme conditions, which are not only increased thermomechanical loads and high sliding speeds, but also, mainly, the effect of a gaseous medium, in particular, vacuum. Detonation-gas spraying was carried out with the developed nanocomposite powders of the Fe-Ti-SiC-MoS2-MgC2 system. Particles of solid lubricant corresponding to fractions of 30-40 μm were mixed with the initial nanopowders by the wet method. To eliminate powder adhesion to the chamber walls and optimize the process of spheroidization of a mixture of its components, we used a developed and tested technology with the use of ultrasound. Tests in vacuum were carried out on a friction machine M-22PV, designed for laboratory and experimental evaluation of tribological characteristics and quality control of coatings. Investigation of the wear resistance of coatings during friction, their tendency to set were evaluated by the intensity of wear in a vacuum (at a vacuum of 1.33×10-5 Pa). The study of the quality of surface layers, in which the processes of activation during friction proceed, were carried out using modern methods of physicochemical studies, including metallography, scanning electron microscopy, and X-ray structural phase analysis. As a result of external influences and the relative movement of the contact surfaces, the first and main manifestation of external friction arises - elastoplastic deformation, which causes the emergence of a set of surface phenomena that determine the essential properties and qualitative regularities of friction processes. The results of metallographic analysis and surface studies confirm the presence of a surface passivating film of molybdenum disulfide. The use of the optimal combination of the properties of MoS2 and graphite films significantly improves the tribotechnical characteristics. The recommended graphite content, as established, is 10-12% (wt.%), which corresponds to the maximum lubricating effect of the formed complex film, which prevents the adhesion interaction of juvenile surfaces, while individual foci of destruction are localized in the near-surface layers and annihilate in the process of grain boundary sliding, excluding any kind of damage.

Research of sliding friction pairs of powder coatings with metal counterbodies in conditions of low temperatures

Role of transfer film formation on the tribological properties of polymeric composite materials and spherical plain bearing at low temperatures

Research on the Friction and Wear Mechanism of a Polymer Interface at Low Temperature Based on Molecular Dynamics Simulation

Influence of the chemical composition of the material and the physical and mechanical properties of the coating on the wear resistance of the "shaft — coating — bearing bush" tribological coupling

Efficiency of Antifriction Solid Lubricant Coatings for Metal–Polymer Friction Pairs

ACCELERATED TESTING OF MECHANICAL AND CHEMICAL EFFECT OF THE ENVIRONMENT ON WEAR RESISTANCE OF PARTS OF TRIBOCOUPLES UNDER COMPLEX DYNAMIC LOADING

Effect of the Material and Sliding Rate of the Counterface on the Tribotechnical Properties of a CM(Ti–Mo–BN)–Steel Friction Pair

Wear and Contact Temperature Evolution in Pin-on-Disc Tribotesting of Low-Metallic Friction Material Sliding Against Pearlitic Cast Iron

Comparison of tribological properties of a DLC jointly with steel / ceramics under dry friction and boundary lubrication

Sliding Wear of Cast-Iron Coatings and Cast-Iron-cast-iron Pairs in Lubricated Contact

The Tribological Behavior of Ni–Cu–Ag-based PVD Coatings for Hybrid Bearings under Different Lubrication Conditions

Engineering Relationships for Computational and Analytical Prediction of Coating Wear during Tribological Tests

Study on the Tribological Properties of PTFE-Based Composites Materials Sliding Pair under Extreme Environment

Method for Determining the Coefficient of Friction Variation Pattern as a Function of Density at Low Temperatures Using the Example of Dry Ice–Steel Contact

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

WEAR RESISTANCE OF NANOCOMPOSITE COATINGS IN VACUUM

MICROSTRUCTURES AND WEAR-RESISTANCE BEHAV-IORS OF FERROUS SULFIDE COATINGS

Pin-on-Disc Testing of Low-Metallic Friction Material Sliding Against HVOF Coated Cast Iron: Modelling of the Contact Temperature Evolution

Static friction measurement methodology for the assessment of performance of industrial valves at high temperatures: Case study for a nickel-based alloy coating

Friction and Wear Behavior of PTFE-based Composites under Dry Sliding and in Liquid Nitrogen

Mechanisms of transferring the matter in a friction process in a tribology system: polymeric composite-metal