Abstract:Due to their remarkable properties, such as high latent heat and stable temperatures during phase transitions, phase change materials (PCMs) are widely used in thermal energy storage (TES) and thermal management systems (TMSs). However, their low thermal conductivity has limited their broader application across various industries. This study experimentally explores, for the first time, the effects of injecting boiling fluid (BF) into the PCM container as a new method to enhance heat transfer during the solidification process of PCM. To this end, Paraffin wax and acetone with saturation temperature lower than paraffin's freezing point are selected as PCM and BF, and the influence of four various parameters, namely the initial PCM temperature (75, 85, and 95 °C), the height of the PCM inside the container (15 cm, 25 cm, and 35 cm), the flow rate of the BF (0.32, 0.46, and 0.57 L/min), and the nozzle diameter (2 mm, 3 mm, and 4 mm), on the solidification behavior of PCM, temperature distribution inside the container, and heat transfer enhancement (released energy and Nusselt number) is thoroughly scrutinized. In order to visualize and further evaluate the two simultaneous phase transitions (vaporization of the BF and solidification of the PCM), a Hele-Shaw cell with a height, width, and thickness of 50, 20, and 1 cm is considered as the PCM storage system. The findings indicate that when the BF is injected into the paraffin storage, the high heat transfer coefficient of boiling superbly improves the thermal behavior of PCM, and the solidification process occurs in a much shorter time. Also, boiling of the acetone inside the container and its direct contact with paraffin leads to a significant mixing inside the container and the creation of vortices and turbulent flow in the system, which further improves the freezing phenomenon. Furthermore, it was observed that regardless of other parameters, the flow rate of BF is the most crucial parameter, and after that, the height of the paraffin and the initial temperature have the greatest impact. By employing the highest flow rate, the proposed technique is capable of freezing 0.7, 0.5, and 0.3 L of paraffin in 48, 33, and 18 s, respectively, indicating multiple times of improvement in the full solidification time compared to previous studies.

A novel approach for solidification enhancement of phase change materials through direct contact with a boiling fluid: An experimental investigation and visualization

Ultra-fast solidification of phase change materials using the injection of a boiling fluid

Encapsulation of Phase Change Materials Via Interfacial Miniemulsion Polymerization for High Thermal Energy Storage Density

Experimental and Computational Study of Constrained Melting of Phase Change Materials (pcm) Inside A Spherical Capsule

A volume-shrinkage-based method for quantifying the inward solidification heat transfer of a phase change material filled in spherical capsules

Phase Change Materials of Paraffin in H-Bn Porous Scaffolds with Enhanced Thermal Conductivity and Form Stability

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Melting Performance Enhancement of Phase Change Material with Magnetic Particles under Rotating Magnetic Field

Heat transfer enhancement for thermal energy storage using metal foams embedded within phase change materials (PCMs)

Numerical Investigations on Heat Release Performance of Phase Change Mixture of Paraffin and Water

Thermal energy storage of phase change materials in the solidification process inside the quasi‐square heat exchanger: CFD simulation

Experimental and numerical investigations of enhanced thermal energy storage performance for foam/paraffin composite under different heating conditions

Visualized experiment on solid-liquid phase change heat transfer enhancement with multiple PCMs

Solid/liquid phase change heat transfer in latent heat thermal energy storage

Enhancing the performance of thermal energy storage by adding nano-particles with paraffin phase change materials

Experimental and Numerical Study of Heat Transfer Characteristics of a Paraffin/Metal Foam Composite PCM

Enhancing the Melting Process of Shell-and-Tube PCM Thermal Energy Storage Unit Using Modified Tube Design

Thermal Transport Process of Metal Foam/paraffin Composite (MFPC) with Solid-Liquid Phase Change: an Experimental Study

Market-orientated solutions to increase thermal conductivity in latent thermal energy storage systems

Thermal characteristics enhancement of Paraffin Wax Phase Change Material (PCM) for thermal storage applications

Solidification acceleration in a triplex-tube latent heat thermal energy storage system using V-shaped fin and nano-enhanced phase change material