Hassan Waqas,Jahid Hasan,Syed Muhammad Raza Shah Naqvi,Dong Liu,Taseer Muhammad,Sayed M. Eldin,Can Kang,Md. Jahid Hasan
Abstract:Phase change materials (PCMs) are now being extensively used in thermal energy storage (TES) applications. Numerous researchers conducted experiments using various circumstances and materials to optimize storage performance. A study was conducted to compare the numerical research of the melting process of paraffin wax using a hybrid nano-integrated paraffin PCM with graphene oxide (GO) and single-walled carbon nanotubes (SWCNTs) in a TES unit. Hence, this research focuses on a sustainable TES system using hybrid nanomaterials (PCM + GO, PCM + SWCNTs, PCM + GO + SWCNT) with varying concentrations of nanoparticles. The objective is to improve the thermal characteristics of PCMs. The main aim of this study is to examine the numerical analysis of the system inside a TES that has a rectangular form. The numerical experiments were conducted using the finite-volume solver Ansys Fluent. The obtained findings show the thermophysical characteristics fluctuations with respect to the solid volume fractions, liquid fraction, temperature, and velocity inside the TES system. Implementing an effective heat transfer mechanism from the point of capture to storage and later consumption necessitates the employment of a heat transfer fluid. The inclusion of SWCNT particles at a concentration of just 10% has been seen to expedite the melting phenomenon. Furthermore, incorporating GO in conjunction with SWCNT alleviates this phenomenon, resulting in a melting behavior that resembles that of unadulterated paraffin. Additionally, the introduction of just 1% GO, combined with SWCNT, leads to a rapid alteration in surface heat transfer coefficient compared to the scenario with single SWCNT and paraffin. These insights hold practical relevance for the development of TES systems in various applications.
materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to improve the performance of phase - change materials (PCM) in thermal energy storage (TES) systems. Specifically, by adding nanoparticles (such as graphene oxide (GO) and single - walled carbon nanotubes (SWCNTs)) to paraffin - based phase - change materials, the researchers aim to improve their thermophysical properties, especially their thermal conductivity and melting rate.
### Research Background and Problem Description
1. **Importance of Thermal Energy Storage**
- With the increase in energy demand, efficient thermal energy storage (TES) technologies have become crucial. Traditional thermal energy storage methods have some limitations, such as low thermal conductivity and slow charging and discharging rates.
2. **Application of Phase - Change Materials (PCM)**
- Phase - change materials (PCM) are widely used in the field of thermal energy storage because they can absorb and release a large amount of latent heat during the phase - change process. However, the low thermal conductivity of most PCMs limits their application effectiveness.
3. **Introduction of Nanoparticles**
- To overcome the problem of low thermal conductivity of PCM, researchers attempt to introduce nanoparticles (such as GO and SWCNTs) into PCM to form hybrid nanomaterials. These nanoparticles can significantly improve the thermal conductivity and melting rate of PCM.
### Research Objectives
- **Improve Thermophysical Properties**: By adding different concentrations of nanoparticles (GO, SWCNTs and their combinations), study their influence on the thermophysical properties of PCM, including thermal conductivity, melting rate, etc.
- **Optimize Thermal Energy Storage Systems**: Develop a sustainable thermal energy storage system, using hybrid nanomaterials (PCM + GO, PCM + SWCNTs, PCM + GO + SWCNTs) to optimize the thermal performance of the system.
- **Numerical Simulation Analysis**: Use Ansys Fluent for numerical simulation to study the fluid flow, temperature distribution and liquid - phase fraction change in a rectangular thermal energy storage system.
### Main Research Contents
- **Model Setup**: Consider a two - dimensional rectangular geometric structure filled with solid PCM, with the bottom and top boundaries made of aluminum and the side walls made of plexiglass, which has a low thermal conductivity.
- **Boundary Conditions**: Heat from the bottom, keep a low temperature at the top, and the side walls are adiabatic conditions.
- **Mathematical Model**: Based on the mass conservation, momentum conservation and energy conservation equations, combined with the Boussinesq approximation, establish a mathematical model to describe the melting process of PCM.
- **Result Analysis**: Through numerical simulation, analyze the velocity distribution, liquid - phase fraction and temperature distribution at different time steps, and explore the influence of nanoparticle concentration on them.
### Conclusions
By adding nanoparticles to PCM, especially the combination of SWCNTs and GO, the thermal conductivity and melting rate of PCM can be significantly improved, thereby optimizing the performance of the thermal energy storage system. This research result is of great significance for the development of efficient thermal energy storage technologies, especially in the fields of building energy conservation and solar thermal utilization.
Hope this summary can help you understand the research purpose and main content of this paper. If you have any further questions or need more detailed explanations, please feel free to let me know!