Abstract:The study investigated the microstructural characteristics, Laves phase dissolution kinetics, and the homogenization kinetics of Ti, Nb, Mo elements, as well as the hot deformation behavior of ERNiCrMo-3 alloy under different homogenization degrees. The results showed that the precipitated phases in the as-cast ERNiCrMo-3 alloy primarily included carbonitrides (Nb,Ti)CN, δ phase, and Laves phase. Cr and Fe elements exhibited negative segregation, while Al, Mo, Nb, and Ti elements showed positive segregation into the interdendritic regions. The temperature required to completely eliminate the δ phase in the as-cast ERNiCrMo-3 alloy was between 1050 °C and 1100 °C. The dissolution temperature of the Laves phase was above 1200 °C, with a diffusion activation energy of 186.184 kJ/mol. The compound phases of nitrides and Laves phases in the alloy were found and dissolved upon exceeding 1150 °C, and spinel Mo 2 Nb 2 O 6 as well as oxide Cr 2 O 3 also formed within the alloy after the temperature exceeded 1150 °C. The diffusion activation energies for Ti, Nb, Mo elements, QTi , QNb , QMo , were 265.48, 231.85, 275.69 kJ/mol, with diffusion constants D0 of 2.4E-1, 6.15E-3, 4.4E-1 cm 2 /s, respectively. The low diffusion coefficient and activation energy of Nb element serve as the limiting mechanisms in the homogenization process of the as-cast ERNiCrMo-3. Furthermore, The recrystallization mechanism involved particle-stimulated nucleation initially, transitioning to continuous dynamic recrystallization. The degree of dynamic recrystallization within the ERNiCrMo-3 alloy exhibits an initial decrease followed by an increase. Homogenization enhances hot deformation compatibility and reduces the propensity for hot deformation-induced cracking within the alloy.

Microsegregation and homogenization behavior of CoCrFeMnNi high-entropy alloy

Microsegregation in high-entropy intermetallic compounds

Study on Micro Segregation of High Alloy Fe–Mn–C–Al Steel

Understanding the physical metallurgy of the CoCrFeMnNi high-entropy alloy: an atomistic simulation study

Effect of Cr Segregation on Mechanical Behavior and Deformation Mechanism of Ni─Co─Cr Alloy

Effect of Solidification Segregation on Microstructure and Mechanical Properties of a Ni-Cr-Mo-V Steel Weld Metal

On the Solidification and Phase Stability of a Co-Cr-Fe-Ni-Ti High-Entropy Alloy

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Towards the equiaxed grain microstructure in CrMnFeCoNi high‐entropy alloy fabricated by directed energy deposition

Impact of 3d TM elements on Cu segregation in CrCuTiV-based high entropy alloys and their mechanical properties

Homogenization Heat Treatment of CoCrCuMnNi High-Entropy Alloys: Limitations and Challenges

Exceptional thermal stability of nanostructured FeCoNiCrCu high entropy alloy facilitated by unusual grain boundary segregation

Sintering mechanism and microstructure evolution of a CoCrFeNiMn high entropy alloy fabricated by metal injection molding

The influence of homogenization on the microstructure and high-temperature mechanical properties of ERNiCrMo-3 alloy

Effect of short-range ordering and grain boundary segregation on shear deformation of CoCrFeNi high-entropy alloys with Al addition

Influence of W, Mo and Ti trace elements on the phase separation in Al8Co17Cr17Cu8Fe17Ni33 based high entropy alloy

High-throughput assessment of the microstructural stability of segregation-engineered nanocrystalline Al-Ni-Y alloys

Microstructural Evolution and Mechanical Properties of Non-Equiatomic (CoNi)74.66Cr17Fe8C0.34 High-Entropy Alloy

Study of Cu Effect and In-situ Yttria Dispersoids on Microstructure Evolution of Mechanically Alloyed CoFeNiCrCu High Entropy Alloys

Hot Deformation Characteristics and Microstructure Evolution of CoCrFeNiZr0.3 Hypoeutectic High-Entropy Alloy

Segregation Behavior of Alloying Elements in Different Oriented Single Crystal Nickel Based Superalloys