Abstract:Statement of problem: Computer-aided design and computer-aided manufacturing (CAD-CAM) methodologies allow the fabrication of custom dental implant abutments with a variety of materials and techniques. Studies on the mechanical strength of such components and the wear induced at their coupling interface during mechanical cycling are sparse. Purpose: The purpose of this in vitro study was to measure the wear patterns at the hexagonal platform of dental implants induced by the installation and mechanical cycling of custom abutments fabricated by using 4 different CAD-CAM methods and to determine the compressive static resistance of the implant-abutment combinations. Material and methods: A CAD software program was used to design a custom abutment for a single-unit screw-retained external hexagon dental implant crown. The same design file was used to manufacture with 4 CAM methods (N=40): milling and sintering of zirconium dioxide (ZO), cobalt-chromium (Co-Cr) sintered by selective laser melting (SLM), fully sintered machined Co-Cr alloy (MM), and machined and sintered agglutinated Co-Cr alloy powder (AM). Prefabricated titanium abutments were used as a control (TI). Each abutment was installed onto a dental implant (4.1×11 mm), and the specimens were mechanically aged (1 million cycles, 2 Hz, 100N, 37 °C). After mechanical cycling, the hexagonal connection of the dental implants was examined with a scanning electron microscope (SEM), and unused dental implants (NI) were examined as a control (n=10). The images were analyzed with a software program to quantify the areas that showed wear. The implant-abutment combinations were reassembled and submitted to a compression test (1mm/min) with a universal testing machine. The data obtained were submitted to 1-way ANOVA (α=.05). Results: The mean ±standard deviation fracture load (N) of the specimens of each group were 1005 ±187 (ZO), 1074 ±123 (SLM), 1033 ±109 (MM), 1019 ±149 (AM), and 923 ±129 (TI). These values were statistically similar (P=.213). The mean ±standard deviation wear of the implants in squared-pixels were 1.1 ±0.38×105 (ZO), 2.0 ±0.29×105 (SLM), 1.0 ±0.38×105 (MM), 1.1 ±0.27×105 (AM), 1.1 ±0.33×105 (TI), and 0.51 ±0.29×105 (NI). The results indicated that, although significantly higher than those in in the control group (NI), the wear values found in the groups TI, ZO, MM, and AM were significantly lower than in the SLM group (P<.001). Conclusions: The CAD-CAM abutments presented the same mechanical fracture load and wear measurements as the TI group, except for the SLM material, which showed increased wear. The failure mode from the load bearing test was the fracture of the abutments for the ZO group. The implants permanently deformed or fractured for the metal abutment groups.

In vitro performance of zirconia and titanium implant/abutment systems for anterior application

In vitro performance and fracture resistance of CAD/CAM-fabricated implant supported molar crowns

The Fracture Resistance Comparison between Titanium and Zirconia Implant Abutments with and without Ageing: Systematic Review and Meta-Analysis

Fracture Resistance of Zirconia Oral Implants In Vitro: A Systematic Review and Meta-Analysis

Biomechanical evaluation of anterior implants associated with titanium and zirconia abutments and monotype zirconia implants

Influence of straight versus angulated screw channel titanium bases on failure loads of two-piece ceramic and titanium implants restored with screw-retained monolithic crowns: An in-vitro study

Mechanical stability of posterior implant-supported monolithic zirconia cantilever on titanium-base abutments. An in vitro study

Fracture behaviour of implant–implant- and implant–tooth-supported all-ceramic fixed dental prostheses utilising zirconium dioxide implant abutments

Load fatigue performance of implant-ceramic abutment combinations

Mechanical behavior of zirconia and titanium abutments before and after cyclic load application

Alumina-reinforced zirconia implants: survival rate and fracture strength in a masticatory simulation trial

Mechanical Factors Implicated in Zirconia Implant Fracture Placed within the Anterior Region—A Systematic Review

Fracture Resistance of Zirconia Abutments with or without a Titanium Base: An In Vitro Study for Tapered Conical Connection Implants

Dental implant-abutment fracture resistance and wear induced by single-unit screw-retained CAD components fabricated by four CAM methods after mechanical cycling

Influence of zirconia abutment preparation on the fracture strength of single implant lithium disilicate crowns after chewing simulation

Fracture Resistance and Failure Mode of Monolithic Zirconia, Veneered Zirconia, and Metal-Ceramic Full-Coverage Restorations: A Comparative In Vitro Study

Are implants more reliable than severely compromised endodontically treated teeth as abutments for zirconia-based FPDs? : In vitro results of long-term preclinical load simulation

A comparative finite element analysis of titanium, poly-ether-etherketone, and zirconia abutment on stress distribution around maxillary anterior implants

Effects of screw channel angulation on the fracture resistance of one-piece zirconia crown with titanium base

Mechanical behavior of titanium and zirconia abutments at the implant-abutment interface: A systematic review

Influence of CAD/CAM Abutment Heights on the Biomechanical Behavior of Zirconia Single Crowns