Abstract:This paper presents a comprehensive review of recent studies in electrical power generation from various thermal-consuming processes. In particular, the paper concentrates on TEG technology in recovering waste heat from industrial applications such as chimneys and automotive engines. Studies conclude that TEGs have a lower conversion efficiency (ranging between 5% and 10%), leading to low power output. Also, they state that most of the available TEGs have low operating temperatures limiting their commercial use. Therefore, an effort is taken to understand the key parameters that influence the performance of a thermoelectric generator. It is shown that a large temperature difference across the module, high heat dissipation from the cold side of the TEG and using thermoelectric materials with a high figure of merit generally improve the performance of the thermoelectric generator system. TEG module's cold-side temperature has a large effect on the power output than the hot-side temperature. Several geometric optimization methods, such as flaps and heat spreaders under natural convection resulted in a 129% and 42% increase in TEG power output, respectively. The survey also shows that forced cooling using side-mounted fans produces 58.6% more power compared to the top-mounted fan on the heat sink. However, optimization in fan selection is required to ensure that the power produced by forced cooling is sufficient to run the fans and output higher than the natural convection cooling case. Several studies also show that most of the commercially available TEG modules made from Bismuth telluride suffer from low operating temperature (maximum of 2600C) and have figure of merit of 1.2 maximum and low conversion efficiency (up to 5%). Recommendations are made to further research alternatives like SiGe alloys, clathrates, skutterudites, and complementary metal-oxide semiconductors with better temperature ranges and figures of merit.The carrier transport processes in thermoelectric materials are significantly correlated with the performance of thermoelectric devices (TEs), which is modeled in this study considering the drift-diffusion equation with thermoelectric contributions for detailing the effects of carrier transport on the yielded current density. A micro thermoelectric generator (μTEG) with boron and arsenic being respectively doped into Si0.7Ge0.3 for p-type and n-type thermoelectric materials is employed as the study case by the three-dimensional numerical simulation to reveal the effects of doping concentrations on the thermoelectric performance. Based on the simulation results a novel μTEG design that incorporates PN junctions to extract minority carriers to reduce the recombination rates of electrons and holes is proposed. The performances for conventional and the present novel μTEGs at different temperature differences are compared. The results show that there is an optimal doping concentration for the conventional μTEG to peak the output power and the thermoelectric conversion efficiency. In particular, the novel μTEG reveals a significant improvement of thermoelectric efficiency by approximately 20% as the hot-end temperature is above 900 K. The transport of minority carriers by the PN junctions demonstrates the expected effects through the analysis on the vector distribution of minority carrier current density.Thermal stress plays an important role in the lifetime of thermoelectric generators, and its minimization can prolong the usage of the generators. To figure out and efficiently lower the thermal stress, this study analyzes the thermoelectric performance and thermal stress of a thermoelectric module in a waste heat recovery system. The performance of the TEM with varied numbers of square pin fins in a flow channel is examined by computational fluid dynamics. The results indicate that for different numbers of square pin fins, the heat transfer rate of the module's hot side increases as the number of fins increases. When the number of fins increases from 36 to 84, the heat transfer rate improves by 8.57%. In addition, the temperature distribution in the module in a waste heat recovery system is uneven due to differences in heat transfer. Therefore, the thermal stress of the module is uneven, and the maximum thermal stress occurs in the TE legs, which are located at the corners of the module. To reduce the maximum thermal stress, the thicknesses of the ceramic plate and the thermoelectric legs are optimized using the multi-objective genetic algorithm. The optimization results indicate that the maximum thermal stress of the module is proportional to its output power, meaning that as the maximum thermal stress in the module is minimized, its output power will approach the minimum value. Instead, the same method is employed to minimize the maximum thermal stress on the module while maintaining its output -Abstract Truncated-

Design and performance of a modular 1 kilowatt-level thermoelectric generator for geothermal application at medium-low temperature

Optimal design of a high-performance heat exchanger for modular thermoelectric generator towards low-grade thermal energy recovery

Comprehensive review in waste heat recovery in different thermal energy-consuming processes using thermoelectric generators for electrical power generation

Theoretical study on geothermal power generation using thermoelectric technology: a potential way to develop geothermal energy

Experimental study of optimization of thermoelectric modules' number and layout for waste heat recovery

An experimental study on the performance of TEGs using uniform flow distribution heat exchanger for low-grade thermal energy recovery

Configuration Optimization of the Segmented Modules in an Exhaust-Based Thermoelectric Generator for Engine Waste Heat Recovery

Design a new thermoelectric module with high practicability based on experimental measurement

Advantage of a Thermoelectric Generator with Hybridization of Segmented Materials and Irregularly Variable Cross-Section Design

Evaluation of Power Conditioning Architectures for Energy Production Enhancement in Thermoelectric Generator Systems

Thermal management of a flexible controlled thermoelectric energy conversion-utilization system using a multi-objective optimization

A Thermoelectric Generation System and Its Power Electronics Stage

Optimizing the output performance and parasitic depletion of Bi2Te3-based thermoelectric generators by using a high-density approach

Optimizing GeTe-based thermoelectric generator for low-grade heat recovery

Impact of internal connections and heat loss on simulated large-scale low-temperature thermoelectric generation system

Performance Analysis of Thermoelectric System Based on Radiative Cooling and Greenhouse Effects

Performance analysis and design optimization of a compact thermoelectric generator with T-Shaped configuration

Numerical Study on Nonuniform Segmented Enhancement Method for Thermoelectric Power Generator

Power generation and thermal stress characterization of thermoelectric modules with different unileg couples by recovering vehicle waste heat

A Novel Optimization Method for TEG System Performance Based on Temperature and Heat Flux

Evaluation on High-Efficiency Thermoelectric Generation Systems Based on Differential Power Processing