Abstract:Optimization methods have been widely applied to the aerodynamic design of gas turbine blades. While applying optimization to high-fidelity computational fluid dynamics (CFD) simulations has proven capable of improving engineering design performance, a challenge has been overcoming the prolonged run-time due to the computationally expensive CFD runs. Reduced-order models and, more recently, machine learning methods have been increasingly used in gas turbine studies to predict performance metrics and operational characteristics, model turbulence, and optimize designs. The application of machine learning methods allows for utilizing existing knowledge and datasets from different sources, such as previous experiments, CFD, low-fidelity simulations, 1D or system-level studies. The present study investigates inserting a machine learning model that utilizes such data into a high-fidelity CFD driven optimization process, and hence effectively reduces the number of required evaluations of the CFD model. Artificial Neural Network (ANN) models were trained on data from over three thousand two-dimensional (2D) CFD analyses of turbine blade cross-sections. The trained ANN models were then used as surrogates in a nested optimization process alongside a full three-dimensional Navier–Stokes CFD simulation. The much lower evaluation cost of the ANN model allows for tens of thousands of design evaluations to guide the search of the best blade profiles to be used in the more expensive, high-fidelity CFD runs, improving the progress of the optimization while reducing the required computation time. It is estimated that the current workflow achieves a five-fold reduction in computational time in comparison to an optimization process that is based on three-dimensional (3D) CFD simulations alone. The methodology is demonstrated on the NASA/General Electric Energy Efficient Engine (E3) high pressure turbine blade and found Pareto front designs with improved blade efficiency and power over the baseline. Quantitative analysis of the optimization data reveals that some design parameters in the present study are more influential than others, such as the lean angle and tip scaling factor. Examining the optimized designs also provides insight into the physics, showing that the optimized designs have a lower amount of pressure drop near the trailing edge, but have an earlier onset of pressure drop on the suction side surface when compared to the baseline design, contributing to the observed improvements in efficiency and power.

Optimization of Blowing Jet Performance on Wind Turbine Airfoil Under Dynamic Stall Conditions Using Active Machine Learning and Computational Intelligence

Machine learning-based optimization of a pitching airfoil performance in dynamic stall conditions using a suction controller

Stall Margin Improvement in an Axial Compressor by Continuous and Pulsed Tip Injection

Aerodynamic Optimization of a Transonic Fan Rotor by Blade Sweeping Using Adaptive Gaussian Process

Numerical Investigation on the Evolution Process of Different Vortex Structures and Distributed Blowing Control for Dynamic Stall Suppression of Rotor Airfoils

Optimization of Turbine Blade Aerodynamic Designs Using CFD and Neural Network Models

Airfoil Optimization Using a Machine Learning-Based Optimization Algorithm

Machine learning for optimal flow control in an axial compressor

Design Optimization of the Last Stage of a 4.5-Stage Compressor Using a POD-based Hybrid Model

Effects of blowing and suction jets on the aerodynamic performance of wind turbine airfoil

Development and Validation of the IAG Dynamic Stall Model in State-Space Representation for Wind Turbine Airfoils

A computational fluid dynamics analysis on enhancing wind turbine efficiency through synthetic jet actuation

Aeromechanical optimization of first row compressor test stand blades using a hybrid machine learning model of genetic algorithm, artificial neural networks and design of experiments

Numerical Optimization for Stator Vane Settings of Multi-Stage Compressors Based on Neural Networks and Genetic Algorithms

Wing design optimization and stall analysis with Co-flow Jet active control

Numerical simulation and research on improving aerodynamic performance of vertical axis wind turbine by co-flow jet

Three-Dimensional Aerodynamic Optimization Of A Multi-Stage Axial Compressor

CFD simulation and aerodynamic optimization of two-stage axial high-pressure turbine blades

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

Numerical Study of Flow Control to Increase Vertical Tail Effectiveness of an Aircraft by Tangential Blowing